Hydrofluoric acid


Hydrofluoric acid[] is a solution of hydrogen fluoride in water. It is used to make most fluorine-containing compounds; examples include the commonly used pharmaceutical antidepressant medication fluoxetine and the material PTFE. Elemental fluorine is produced from it. Solutions of HF are colourless, acidic and highly corrosive. It is commonly used to etch glass and silicon wafers.
When hydrofluoric acid comes into contact with human skin it causes deep burns.

Uses

Production of organofluorine compounds

The principal use of hydrofluoric acid is in organofluorine chemistry. Many organofluorine compounds are prepared using HF as the fluorine source, including Teflon, fluoropolymers, fluorocarbons, and refrigerants such as freon. Many pharmaceuticals contain fluorine.

Production of inorganic fluorides

Most high-volume inorganic fluoride compounds are prepared from hydrofluoric acid. Foremost are Na3AlF6, cryolite, and AlF3, aluminium trifluoride. A molten mixture of these solids serves as a high-temperature solvent for the production of metallic aluminium. Other inorganic fluorides prepared from hydrofluoric acid include sodium fluoride and uranium hexafluoride.

Etchant, cleaner

It is used in the semiconductor industry as a major component of Wright Etch and buffered oxide etch, which are used to clean silicon wafers. In a similar manner it is also used to etch glass by treatment with silicon dioxide to form gaseous or water-soluble silicon fluorides. It can also be used to polish and frost glass.
A 5% to 9% hydrofluoric acid gel is also commonly used to etch all ceramic dental restorations to improve bonding. For similar reasons, dilute hydrofluoric acid is a component of household rust stain remover, in car washes in "wheel cleaner" compounds, in ceramic and fabric rust inhibitors, and in water spot removers. Because of its ability to dissolve iron oxides as well as silica-based contaminants, hydrofluoric acid is used in pre-commissioning boilers that produce high-pressure steam. Hydrofluoric acid is also useful for dissolving rock samples prior to analysis. In similar manner, this acid is used in acid macerations to extract organic fossils from silicate rocks. Fossiliferous rock may be immersed directly into the acid, or a cellulose nitrate film may be applied, which adheres to the organic component and allows the rock to be dissolved around it.

Oil refining

In a standard oil refinery process known as alkylation, isobutane is alkylated with low-molecular-weight alkenes in the presence of an acid catalyst derived from hydrofluoric acid. The catalyst protonates the alkenes to produce reactive carbocations, which alkylate isobutane. The reaction is carried out at mild temperatures in a two-phase reaction.

Production

Hydrofluoric acid was first prepared in 1771, by Carl Wilhelm Scheele. It is now mainly produced by treatment of the mineral fluorite, CaF2, with concentrated sulfuric acid at ca. 265 °C.
The acid is also a by-product of the production of phosphoric acid from apatite/fluoroapatite. Digestion of the mineral with sulfuric acid at elevated temperatures releases a mixture of gases, including hydrogen fluoride, which may be recovered.
Because of its high reactivity toward glass, hydrofluoric acid is stored in plastic containers.
Hydrofluoric acid can be found in nature, having been released in a volcanic eruption.

Properties

In dilute aquous solution hydrogen fluoride behaves as a weak acid,
Infrared spectroscopy has been used to show that, in solution, dissociation is accompanied by formation of the ion pair ·F.
This ion pair has been characterized in the crystalline state at very low temperature.
Further association has been characterized both in solution and in the solid state.
It is assumed that polymerization occurs as the concentration increases. This assumption is supported by the isolation of a salt of a tetrameric anion anion H3F4
and by low-temperature X-ray crystallography. The species that are present in concentrated aqueous solutions of hydrogen fluoride have not been characterized; the formation of polymeric species, Hn-1Fn, is highly likely.
The Hammett acidity function, H0, for 100% HF is estimated to be between −10.2 and −11. which is comparable to the value −12 for sulfuric acid.
Solutions of hydrofluoric acid attack glass, so they are stored and used in vessels made of teflon. They attack human skin, so must be handled with great care: see #Health and Safety, below.

Acidity

Unlike other hydrohalic acids, such as hydrochloric acid, hydrogen fluoride is only a weak acid in dilute aqueous solution. This is in part a result of the strength of the hydrogen–fluorine bond, but also of other factors such as the tendency of HF,, and anions to form clusters. At high concentrations, HF molecules undergo homoassociation to form polyatomic ions and protons, thus greatly increasing the acidity. This leads to protonation of very strong acids like hydrochloric, sulfuric, or nitric when using concentrated hydrofluoric acid solutions. Although hydrofluoric acid is regarded as a weak acid, it is very corrosive, even attacking glass when hydrated.
The acidity of hydrofluoric acid solutions varies with concentration owing to hydrogen-bond interactions of the fluoride ion. Dilute solutions are weakly acidic with an acid ionization constant , in contrast to corresponding solutions of the other hydrogen halides, which are strong acids. Concentrated solutions of hydrogen fluoride are much more strongly acidic than implied by this value, as shown by measurements of the Hammett acidity function H0. The H0 for 100% HF is estimated to be between −10.2 and −11, comparable to the value −12 for sulfuric acid.
In thermodynamic terms, HF solutions are highly non-ideal, with the activity of HF increasing much more rapidly than its concentration.
The weak acidity in dilute solution is sometimes attributed to the high H—F bond strength, which combines with the high dissolution enthalpy of HF to outweigh the more negative enthalpy of hydration of the fluoride ion. Paul Giguère and Sylvia Turrell have shown by infrared spectroscopy that the predominant solute species in dilute solution is the hydrogen-bonded ion pair ·F.
With increasing concentration of HF the concentration of the hydrogen difluoride ion also increases. The reaction
is an example of homoconjugation.

Production

Hydrofluoric acid is produced by treatment of the mineral fluorite with concentrated sulfuric acid. When combined at 265 °C, these two substances react to produce hydrogen fluoride and calcium sulfate according to the following chemical equation:
Although bulk fluorite is a suitable precursor and a major source of world HF production, HF is also produced as a by-product of the production of phosphoric acid, which is derived from the mineral apatite. Apatite sources typically contain a few percent of fluoroapatite, acid digestion of which releases a gaseous stream consisting of sulfur dioxide, water, and HF, as well as particulates. After separation from the solids, the gases are treated with sulfuric acid and oleum to afford anhydrous HF. Owing to the corrosive nature of HF, its production is accompanied by the dissolution of silicate minerals, and, in this way, significant amounts of fluorosilicic acid are generated.

Health and safety

In addition to being a highly corrosive liquid, hydrofluoric acid is also a powerful contact poison. Because of the ability of hydrofluoric acid to penetrate tissue, poisoning can occur readily through exposure of skin or eyes, or when inhaled or swallowed. Symptoms of exposure to hydrofluoric acid may not be immediately evident, and this can provide false reassurance to victims, causing them to delay medical treatment. Despite having an irritating odor, HF may reach dangerous levels without an obvious odor. HF interferes with nerve function, meaning that burns may not initially be painful. Accidental exposures can go unnoticed, delaying treatment and increasing the extent and seriousness of the injury. Symptoms of HF exposure include irritation of the eyes, skin, nose, and throat, eye and skin burns, rhinitis, bronchitis, pulmonary edema, and bone damage.

Popular culture

In an episode of Breaking Bad titled "Cat's in the Bag...," Jesse Pinkman uses hydrofluoric acid to dissolve the body of Emilio Koyama. In another episode of Breaking Bad entitled “Box Cutter”, Walter White and Jesse Pinkman use hydrofluoric acid to dissolve the body of Victor.
In the film Saw VI, hydrofluoric acid is used for killing William Easton. In the film Jigsaw, Carly is also killed by hydrofluoric acid, injected into her bloodstream.
In an episode of Titans titled "Jason Todd," a young Dick Grayson claims that his parents' murderer used hydrofluoric acid to burn their trapeze ropes.