Thrust reversal


Thrust reversal, also called reverse thrust, is the temporary diversion of an aircraft engine's thrust so that it acts against the forward travel of the aircraft, providing deceleration. Thrust reverser systems are featured on many jet aircraft to help slow down just after touch-down, reducing wear on the brakes and enabling shorter landing distances. Such devices affect the aircraft significantly and are considered important for safe operations by airlines. There have been accidents involving thrust reversal systems, including fatal ones.
Reverse thrust is also available on many propeller-driven aircraft through reversing the controllable-pitch propellers to a negative angle. The equivalent concept for a ship is called astern propulsion.

Principle and uses

A landing roll consists of touchdown, bringing the aircraft to taxi speed, and eventually to a complete stop. However, most commercial jet engines continue to produce thrust in the forward direction, even when idle, acting against the deceleration of the aircraft. The brakes of the landing gear of most modern aircraft are sufficient in normal circumstances to stop the aircraft by themselves, but for safety purposes, and to reduce the stress on the brakes, another deceleration method is needed. In scenarios involving bad weather, where factors like snow or rain on the runway reduce the effectiveness of the brakes, and in emergencies like rejected takeoffs, this need is more pronounced.
A simple and effective method is to reverse the direction of the exhaust stream of the jet engine and use the power of the engine itself to decelerate. Ideally, the reversed exhaust stream would be directed straight forward. However, for aerodynamic reasons, this is not possible, and a 135° angle is taken, resulting in less effectiveness than would otherwise be possible. Thrust reversal can also be used in flight to reduce airspeed, though this is not common with modern aircraft. There are three common types of thrust reversing systems used on jet engines: the target, clam-shell, and cold stream systems. Some propeller-driven aircraft equipped with variable-pitch propellers can reverse thrust by changing the pitch of their propeller blades. Most commercial jetliners have such devices, and it also has applications in military aviation.

Types of thrust reversal systems

Small aircraft typically do not have thrust reversal systems, except in specialized applications. On the other hand, large aircraft almost always have the ability to reverse thrust. Reciprocating engine, turboprop and jet aircraft can all be designed to include thrust reversal systems.

Propeller-driven aircraft

Propeller-driven aircraft generate reverse thrust by changing the angle of their controllable-pitch propellers so that the propellers direct their thrust forward. This reverse thrust feature became available with the development of controllable-pitch propellers, which change the angle of the propeller blades to make efficient use of engine power over a wide range of conditions. Single-engine aircraft tend not to have reverse thrust. However, single-engine turboprop aircraft such as the PAC P-750 XSTOL, Cessna 208 Caravan, and Pilatus PC-6 Porter do have this feature available.
One special application of reverse thrust comes in its use on multi-engine seaplanes and flying boats. These aircraft, when landing on water, have no conventional braking method and must rely on slaloming and/or reverse thrust, as well as the drag of the water in order to slow or stop. In addition, reverse thrust is often necessary for maneuvering on the water, where it is used to make tight turns or even propel the aircraft in reverse, maneuvers which may prove necessary for leaving a dock or beach.

Jet aircraft

On aircraft using jet engines, thrust reversal is accomplished by causing the jet blast to flow forward. The engine does not run or rotate in reverse; instead, thrust reversing devices are used to block the blast and redirect it forward. High bypass ratio engines usually reverse thrust by changing the direction of only the fan airflow, since the majority of thrust is generated by this section, as opposed to the core. There are three jet engine thrust reversal systems in common use:

Target type

The target thrust reverser uses a pair of hydraulically-operated 'bucket' type doors to reverse the hot gas stream. For forward thrust, these doors form the propelling nozzle of the engine. In the original implementation of this system on the Boeing 707, and still common today, two reverser buckets were hinged so when deployed they block the rearward flow of the exhaust and redirect it with a forward component. This type of reverser is visible at the rear of the engine during deployment.

Clam-shell type

The clam-shell door, or cascade, system is pneumatically operated. When activated, the doors rotate to open the ducts and close the normal exit, causing the thrust to be directed forward. The cascade thrust reverser is commonly used on turbofan engines. On turbojet engines, this system would be less effective than the target system, as the cascade system only makes use of the fan airflow and does not affect the main engine core, which continues to produce forward thrust. turbofan of a VC10

Cold stream type

In addition to the two types used on turbojet and low-bypass turbofan engines, a third type of thrust reverser is found on some high-bypass turbofan engines. Doors in the bypass duct are used to redirect the air that is accelerated by the engine's fan section but does not pass through the combustion chamber such that it provides reverse thrust. The cold stream reverser system is activated by an air motor. During normal operation, the reverse thrust vanes are blocked. On selection, the system folds the doors to block off the cold stream final nozzle and redirect this airflow to the cascade vanes. This system can redirect both the exhaust flow of the fan and of the core.
The cold stream system is known for structural integrity, reliability, and versatility. During thrust reverser activation, a sleeve mounted around the perimeter of the aircraft engine nacelle moves aft to expose cascade vanes which act to redirect the engine fan flow. This thrust reverser system can be heavy and difficult to integrate into nacelles housing large engines.

Operation

In most cockpit setups, reverse thrust is set when the thrust levers are on idle by pulling them further back. Reverse thrust is typically applied immediately after touchdown, often along with spoilers, to improve deceleration early in the landing roll when residual aerodynamic lift and high speed limit the effectiveness of the brakes located on the landing gear. Reverse thrust is always selected manually, either using levers attached to the thrust levers or moving the thrust levers into a reverse thrust 'gate'.
The early deceleration provided by reverse thrust can reduce landing roll by a quarter or more. Regulations dictate, however, that an aircraft must be able to land on a runway without the use of thrust reversal in order to be certified to land there as part of scheduled airline service.
Once the aircraft's speed has slowed, reverse thrust is shut down to prevent the reversed airflow from throwing debris in front of the engine intakes where it can be ingested, causing foreign object damage. If circumstances require it, reverse thrust can be used all the way to a stop, or even to provide thrust to push the aircraft backward, though aircraft tugs or towbars are more commonly used for that purpose. When reverse thrust is used to push an aircraft back from the gate, the maneuver is called a powerback. Some manufacturers warn against the use of this procedure during icy conditions as using reverse thrust on snow- or slush-covered ground can cause slush, water, and runway deicers to become airborne and adhere to wing surfaces.
If the full power of reverse thrust is not desirable, thrust reverse can be operated with the throttle set at less than full power, even down to idle power, which reduces stress and wear on engine components. Reverse thrust is sometimes selected on idling engines to eliminate residual thrust, in particular in icy or slick conditions, or when the engines' jet blast could cause damage.

In-flight operation

Some aircraft, notably some Russian and Soviet aircraft, are able to safely use reverse thrust in flight, though the majority of these are propeller-driven. Many commercial aircraft, however, cannot. In-flight use of reverse thrust has several advantages. It allows for rapid deceleration, enabling quick changes of speed. It also prevents the speed build-up normally associated with steep dives, allowing for rapid loss of altitude, which can be especially useful in hostile environments such as combat zones, and when making steep approaches to land.
The Douglas DC-8 series of airliners has been certified for in-flight reverse thrust since service entry in 1959. Safe and effective for facilitating quick descents at acceptable speeds, it nonetheless produced significant aircraft buffeting, so actual use was less common on passenger flights and more common on cargo and ferry flights, where passenger comfort is not a concern.
The Hawker Siddeley Trident, a 120- to 180-seat airliner, was capable of descending at up to 10,000 ft/min by use of reverse thrust, though this capability was rarely used.
The Concorde supersonic airliner could use reverse thrust in the air to increase the rate of descent. Only the inboard engines were used, and the engines were placed in reverse idle only in subsonic flight and when the aircraft was below 30,000 ft in altitude. This would increase the rate of descent to around 10,000 ft/min.
The Boeing C-17 Globemaster III is one of the few modern aircraft that uses reverse thrust in flight. The Boeing-manufactured aircraft is capable of in-flight deployment of reverse thrust on all four engines to facilitate steep tactical descents up to 15,000 ft/min into combat environments. The Lockheed C-5 Galaxy, introduced in 1969, also has in-flight reverse capability, although on the inboard engines only.
The Saab 37 Viggen also had the ability to use reverse thrust both before landing, to shorten the needed runway, and taxiing after landing, allowing many Swedish roads to double as wartime runways.
The Shuttle Training Aircraft, a highly modified Grumman Gulfstream II, used reverse thrust in flight to help simulate Space Shuttle aerodynamics so astronauts could practice landings. A similar technique was employed on a modified Tupolev Tu-154 which simulated the Russian Buran space shuttle.

Effectiveness

The amount of thrust and power generated are proportional to the speed of the aircraft, making reverse thrust more effective at high speeds. For maximum effectiveness, it should be applied quickly after touchdown. If activated at low speeds, foreign object damage is possible. There is some danger of an aircraft with thrust reversers applied momentarily leaving the ground again due to both the effect of the reverse thrust and the nose-up pitch effect from the spoilers. For aircraft susceptible to such an occurrence, pilots must take care to achieve a firm position on the ground before applying reverse thrust. If applied before the nose-wheel is in contact with the ground, there is a chance of asymmetric deployment causing an uncontrollable yaw towards the side of higher thrust, as steering the aircraft with the nose wheel is the only way to maintain control of the direction of travel in this situation.
Reverse thrust mode is used only for a fraction of aircraft operating time but affects it greatly in terms of design, weight, maintenance, performance, and cost. Penalties are significant but necessary since it provides stopping force for added safety margins, directional control during landing rolls, and aids in rejected take-offs and ground operations on contaminated runways where normal braking effectiveness is diminished. Airlines consider thrust reverser systems a vital part of reaching a maximum level of aircraft operating safety.

Thrust reversal-related accidents and incidents

In-flight deployment of reverse thrust has directly contributed to the crashes of several transport-type aircraft: