Tanks of the United States
This article on military tanks deals with the history and development of American tanks: their origin during World War I; the interwar period; World War II; the Cold War; and the modern era.
World War I
The U.S. Armed Forces entered the First World War on the side of the Entente Powers in April, 1917, without any tanks of their own. The following month, in light of a report into British and French theories on tank operation, the American Expeditionary Forces' commander-in-chief, Gen. John Pershing, decided that both light and heavy tanks were essential for the conduct of the war and should be acquired as soon as possible. A joint Anglo-American program was launched to develop a new heavy tank, of similar design to the British Mark IV tanks. It was, however, expected that sufficient quantities of tanks would not be available until April 1918. The Inter-Allied Tank Commission decided that, because of the wartime demands on French industry, the quickest way to supply the American forces with armor was to manufacture the Renault FT light tank in the United States. Some heavy tanks would also be supplied by Great Britain.Captain Dwight Eisenhower, later General Eisenhower of World War II fame, had gone to Camp Meade, Maryland, in February 1918 with the 65th Engineer Regiment, which had been activated to provide the organizational basis for the creation of the Army's first heavy tank battalion. In mid-March the 1st Battalion, Heavy Tank Service was ordered to prepare for movement overseas, and Eisenhower went to New York with the advance party to work out the details of embarkation and shipment with port authorities. The battalion shipped out on the night of March 26, however Eisenhower did not join them. He had performed well as an administrator, and upon his return to Camp Meade, he was told he would be staying in the United States, where his talent for logistics would be put to good use in establishing the Army's primary tank training center at Camp Colt in Gettysburg, Pennsylvania. Eisenhower became the #3 leader of the new tank corps and rose to the temporary rank of Lieutenant Colonel in the National Army and trained tank crews at "Camp Colt"–his first command–on the grounds of "Pickett's Charge" on the Gettysburg, Pennsylvania Civil War battle site. The American Army in France had Captain George S. Patton, as the first officer assigned to train the crews.
The M1917 was the U.S.'s first mass-produced tank, a license-built near-copy of the French Renault FT. The US Army ordered approximately 4,440 M1917s between 1918 and 1919, receiving about 950 before canceling the contract. A requirement of 1,200 was decided, later increased to 4,400, and some sample Renault tanks, plans, and various parts were sent to the US for study. The design was to be carried out by the Ordnance Department, under the job title "Six-ton Special Tractor," and orders for the vehicles placed with private manufacturers. However, the project was beset by problems: the French specifications were in metric, and thus incompatible with American machinery; coordination between military departments, suppliers, and manufacturers was poor; bureaucratic inertia, lack of cooperation from military departments, and possible vested interests all delayed progress.
The Army in France was expecting the first 300 M1917s by April, 1918, but by June, production had yet to begin, which forced the US to acquire 144 Renault FTs from the French. Production of the M1917 did not begin until the autumn, and the first completed vehicles emerged in October. Two arrived in France on November 20, nine days after the end of hostilities, and a further eight in December.
The Ford 3-Ton M1918 was one of the first light tank designs by the U.S. It was a small two-man, one-gun tank, armed with a M1919 Browning machine gun and capable of a maximum speed of 8 mph. Design on the 3-ton tank started in mid-1918. The 3-Ton was a two-man tank designed so that American forces could use another tank besides the Renault FT. Its twin Model T Ford engines were controlled by the driver, while the gunner sat beside him and controlled a.30/06 machine gun on a limited-traverse mount.
A contract for 15,000 of these vehicles was awarded; however, the U.S. Tank Corps felt that the design did not meet their requirements. The contract for the 15,000 tanks was ended after the Armistice, leaving only fifteen vehicles produced.
Post-World War I
After the end of the conflict, the U.S. Army was reorganized. In 1919, Pershing recommended to a joint session of the Senate and House Committee on Military Affairs that the tank be subordinated to the infantry. As a result, the 1920 National Defense Act disbanded the U.S. Tank Corps, and reassigned its tanks to the infantry branch, with only two heavy tank battalions and four light tank battalions escaping post-war demobilization.The M1917 tanks came too late, and did not take part in any combat during the war. Afterwards, however, five accompanied the U.S. Marine Expeditionary Force to Tientsin in April 1927 under General Smedley Butler. They returned to the U.S. in late 1928. After the Tank Corps was abolished as a separate branch, and control of tanks handed to the infantry, the number of tank units was progressively reduced, and the vehicles mothballed or scrapped.
The Tank Mark VIII was an Anglo-American tank design of the First World War, a collaborative effort to equip France, the U.K., and the U.S. with a single heavy tank design built in France for an offensive in 1919. Testing of the design was not finished until after the war, and it was decided to build 100 vehicles in the U.S.; these were constructed in 1919 and 1920. The American Liberty tanks equipped a single unit: the 67th Infantry Regiment, based in Aberdeen, Maryland. The curious designation of the unit had its origin in the fact that since 1922 by law all tanks had to be part of the Infantry. Some Liberty tanks were assigned to the 301st Tank Battalion, later redesignated the 17th Tank Battalion. Throughout most of 1921–1922, Major Dwight D. Eisenhower commanded this unit.
Although the tank of World War I was slow, clumsy, difficult to control, and mechanically unreliable, its value as a weapon had been clearly demonstrated. In addition to the light and heavy categories of American-produced tanks of World War I, a third classification, the medium, began receiving attention in 1919. The meaning of the terms light, medium, and heavy tanks changed between the wars. During World War I and immediately thereafter, the light tank was considered to be up to 10 tons, the medium was roughly between 10 and 25 tons, and the heavy was over 25 tons. Later, during World War II, increased weights resulted in light tank designs often weighing over 20 tons, medium tank designs weighing over 30 tons, and heavy tank designs weighing over 60 tons.
Patton and Eisenhower remained involved in developing the armored arm, which found a temporary home at Camp Meade under Rockenbach's command. In particular, the two men formulated theory and doctrine for the use of tanks in mass formations to achieve breakthroughs and carry out flanking attacks. They were met with vigorous opposition to their ideas from senior army officers, who favored the use of armor to support the infantry, not as a separate arm conducting independent operations. Congress took this view as well, when enacting the 1920 legislation that dissolved the Tank Corps as a separate entity.
The National Defense Act of 1920 placed the Tank Corps under the Infantry. Patton had argued for an independent Tank Corps, and understood that tanks operating with Cavalry would stress mobility, while tanks tied to the Infantry would emphasize firepower. However, the supply of slow World War I tanks and the subordination of tanks to the infantry branch impeded the development of any role other than direct infantry support, so the United States moved slowly in the development of armored and mechanized forces. Not incidentally, funding for tank research and development was also cut to a bare minimum. Patton, convinced there was no future in tanks, applied and received a transfer to the cavalry in September, 1920. Eisenhower got out two years later, in January 1922, when he was assigned to the staff of an infantry brigade in Panama.
The U.S. War Department considered that two types of tanks, the light and the medium, should fulfill all missions. The light tank was to be transportable by truck, and not exceed 5 tons gross weight. The medium tank was not to exceed 15 tons, so as to bring it within the weight capacity of railroad flatcars. Although an experimental 15-ton tank, the M1924, reached the mock-up stage, this and other attempts to satisfy War Department and infantry specifications proved to be unsatisfactory. In reality, it was simply impossible to build a 15-ton vehicle meeting both War Department and infantry requirements.
In 1926 the General Staff reluctantly consented to the development of a 23-ton tank, although it made clear that efforts were to continue toward the production of a satisfactory 15-ton vehicle. The infantry decided, too, that a light tank, transportable by truck, best met infantry requirements. The net effect of the infantry's preoccupation with light tanks, and the limited funds available for tank development in general, was to slow the development of heavier vehicles and, ultimately, to contribute to the serious shortage of medium tanks at the outbreak of World War II.
In the United States the real beginning of the Armored Force was in 1928, twelve years before it was officially established, when Secretary of War Dwight F. Davis directed that a tank force be developed in the Army, after observing the maneuvers in England, by the British Experimental Armoured Force. Secretary Davis' 1928 directive for the development of a tank force resulted in the assembly and encampment of an experimental mechanized force at Camp Meade, Maryland, from 1 July to 20 September 1928. The combined arms team consisted of elements furnished by Infantry, Cavalry, Field Artillery, the Air Corps, Engineer Corps, Ordnance Department, Chemical Warfare Service, and Medical Corps. An effort to continue the experiment in 1929 was defeated by insufficient funds and obsolete equipment, but the 1928 exercise did bear fruit, for the War Department Mechanization Board, appointed to study results of the experiment, recommended the permanent establishment of a mechanized force.
Despite inadequate funding, the Ordnance Department managed to develop several experimental light and medium tanks, and also worked with J. Walter Christie to test a Christie design model by 1929. None of these tanks were accepted, usually because each of them exceeded standards set by other Army branches. Patton later worked closely with Christie to improve the silhouette, suspension, power, and weapons of the tanks. Christie's ideas had a great impact upon tank tactics and unit organization in many countries and, finally, upon the U.S. Army as well.
Another General who rose to fame in World War II, whose influence on the tanks of the Army was felt, came from the top. On November 21, 1930 Douglas MacArthur had been made Chief of Staff, with the rank of General. As Chief of Staff from 1930 to 1935, Douglas MacArthur wanted to advance motorization and mechanization throughout the Army. In late 1931 all arms and services were directed to adopt mechanization and motorization, and were permitted to conduct research and to experiment as necessary. The Cavalry was given the task of developing combat vehicles that would enhance its role of reconnaissance, counterreconnaissance, flank action, and pursuit.
By the law passed, tanks belonged to the infantry branch, so the cavalry gradually bought a group of "combat cars," lightly armored and armed tanks that were often indistinguishable from the newer infantry, "tanks." In 1933 MacArthur set the stage for the coming complete mechanization of the cavalry, noting the horse was obsolete declaring, "The horse has no higher degree of mobility today than he had a thousand years ago. The time has therefore arrived when the Cavalry arm must either replace or assist the horse as a means of transportation, or else pass into the limbo of discarded military formations."
In November 1936, the U.S. Army's cavalry branch decided to modernize and needed a fully armored vehicle, capable of keeping up with the cavalry and of fulfilling regular combat duties. Prohibited from developing tanks by the National Defense Act of 1920, it could not develop a "tank" in the conventional sense, so opted for a smaller and lighter "car" class vehicle. It came up with the T7 Combat Car designed and built at the Rock Island Arsenal between 1937 and 1938, and was based on the M1 Combat Car but with an extended chassis and a convertible suspension - the ability to travel using wheels or tracks. The only prototype T7 Combat Car was shipped to Aberdeen Proving Grounds in August 1938 for testing. While it showed good speed and performance, cavalry branch representatives were not significantly impressed. Tests were delayed until 1939, but they were reasonably successful. The vehicle even participated in the First Army maneuvers at Plattsburgh, New York in 1939, where the cavalrymen liked it. However, in October 1939, the cavalry branch formed new requirements for their combat vehicles which specified regular tracked suspension. The reason for that decision was that the tracks were already available in reasonable quantity and quality and thus there was no need for the complexity and higher cost associated with convertible vehicles. Furthermore, the heavy machine gun was determined insufficient for the role. The ongoing war in Europe at the time proved that, in order for a vehicle to be successful, it needed a proper cannon. In October 1939, despite its potential, the Mechanized Cavalry Board recommended further development and test of the T7 Combat Car program, and all other such convertible vehicles, be canceled. Thus ended the last wheel-tracked combat vehicle development for the U.S. Army.
Inter War
T7 Combat Car
was a prototype United States light tank design of the inter war period. It could run on either road wheels or tracks, depending on terrain. Although adequate in some areas, it lacked the firepower of contemporary vehicles, and the project was cancelled after only one was built.M1 Combat Car and M2 Light Tank
The M1 Combat Car was a tankette that entered use with the U.S. Cavalry in the late 1930s.Under the terms of the Defense Act of 1920, tanks were restricted to infantry units, which were equipped with M1 tanks armed with twin machine gun turrets by 1935. To allow U.S. Army cavalry units to be equipped with armored fighting vehicles, the tanks developed for the cavalry were designated "combat cars". The Cavalry branch opted for a single, larger turret to be mounted on their M1s.
Other upgrades included improved suspension, improved transmission, and better engine cooling. The Combat Car designation was dropped in 1940, and the vehicle was renamed as the light tank M1A2.
" on display at Patton Cavalry and Armor Museum, Fort Knox, KY.
The next tank to come out, the M2 Light Tank, was developed in 1935 by Rock Island Arsenal for the infantry branch of the U.S. Army. The design originated from the earlier T1 and 1929 T2 Medium Tank designs, and drew limited inspiration from the Vickers 6-ton. Its main weapon was one.50 caliber M2 Browning machine gun, and one.30 caliber machine gun, both installed in a small, one-man turret. After only 10 units were delivered, the Infantry branch decided to switch to a twin turret configuration, with the.30-caliber machine gun moved to a second turret. These early twin-turret tanks were nicknamed "Mae West" by the troops, after the popular busty movie star. The twin-turret layout was inefficient, but was a common feature of 1930s light tanks derived from the Vickers, such as the Soviet T-26 and Polish 7TP.
An improved version of the M2 Light Tank, known as the M2A4, armed with a high-velocity 37 mm gun and coaxial machine gun in a single turret, served with the Marines' 1st Tank Battalion on Guadalcanal in 1942-43. The M2A4 was the only model of the M2 line to see combat.
The Rock Island Arsenal also started work on a new medium tank, based on the design of the M2 Light Tank. Initially designated the T5, the redesigned model was redesignated as the M2 Medium Tank in June, 1939.
T1 light tank and T2 medium tank
The T1 Light Tank and T2 Medium Tank were prototypes that were designed in the 1920s but soon became obsolete, although they would help development with later tanks.Marmon Herrington light tanks
The Marmon-Herrington Combat Tank Light was a US light tank produced for the export market at the start of the Second World War. The CTL-3 had a crew of two and was armed with three.30 caliber machine guns.A few saw combat in the Dutch East Indies campaign against the Japanese invasion., 1945.
In mid-1942 a batch was diverted to Australia from the Dutch order where they were used for training
After the attack on Pearl Harbor some of these tanks were taken over by the United States Army and employed in Northern Alaska as the T14 and T16 respectively.
There were also sent to the Nationalist forces fighting the Japanese as more than 600 of the T16 CTMS tanks were delivered to China under Lend-Lease after Pearl Harbor.
M2 Medium tank
The M2 Medium Tank was a larger development of the M2 Light Tank and was first produced in 1939 by the Rock Island Arsenal, just prior to the commencement of the war in Europe. Many components were common or used a similar design, including the vertical volute spring suspension which would be used in later tanks as well. Twin-wheeled bogies were mounted externally, and rubber-bushed and rubber-shoed track proved durable on roads. The initial M2 model was powered by an air-cooled Wright R-975 radial engine. For the M2A1, this engine was supercharged to provide an extra for a total of, and designated as the R-975 C1 radial engine.The M2 Medium Tank's unique features included an unusually large number of machine guns, bullet deflector plates, and sloped armor on the hull front. The main armament was a 37 mm gun, with 32 mm armor; the M2A1 had a 51 mm gun mantlet. The features of the M2 series development, both good and bad, provided many lessons for U.S. tank designers that were later applied with great success in the M3 Lee, M4 Sherman and many other armored fighting vehicles.
Production for the M2 Medium Tanks was 18 M2 tanks, and 94 slightly improved M2A1 tanks, for a total figure of 112. For combat it was a poor design, with thin armor, inadequate main armament and a high-profile. The four sponson-mounted machine guns proved to be completely unnecessary. But it provided important lessons that were used for the later M3 and M4 medium tanks. In particular, the M2's sloped frontal hull armor was extremely advanced for a 1939 design, and would become a permanent feature of U.S. tank design. Events in Western Europe and on the Eastern Front rapidly demonstrated that the M2 was obsolete, and it was never used overseas in combat; it was used for training purposes throughout the war.
Chrysler opened a new tank plant, the Detroit Arsenal Tank Plant, to manufacture the M2, and the US Government contracted in August, 1940 for 1,000 vehicles to be produced. As events in Europe made obvious that the M2 was obsolete, the government modified the contract before production began. Instead of M2 medium tanks, the plant would now build 1,000 M3 Grant tanks. Production of the M2 was returned to the Rock Island Arsenal, where 94 M2A1s were eventually built. The M2A1 had slightly better armor and a slightly larger turret than the original M2, since it had the turret from the M3 Light Tank, with gun mantlet armor 2 inches thick.
World War II
Light tanks
M3 Light Tank and M5 Light Tank
The M3 Light Tank was an upgrade of the M2 Light Tank. The Battle of France gave momentum to the US tank program because US observers saw how easily British and French light tanks were decimated by German Panzers, and in July 1940 work began on a new light tank based on the M2 series.The initial upgrade was designated the M3 Light Tank, and had thicker armor, modified suspension and a 37 mm gun. Production of the M3 and later the M5 Stuart started in March 1941 and continued until October 1943 with a total of 25,000 produced.
An upgrade of the M3, which was initially called M4 but later redesignated the M5, was developed with improved engines and produced through 1942. The M5 featured a redesigned hull and driver's hatches moved to the top. There was a M7 tank designed based on the Sherman tank, but was so heavy it had to be reclassified as a medium tank and was not mass produced, with only 13 made. The M5 gradually replaced the M3 in production from 1942 and was in turn succeeded by the Light Tank M24 in 1944.
The British Army was the first to use the M3 in combat. In November 1941, some 170 Stuarts took part in Operation Crusader, with poor results.
Although the high losses suffered by Stuart-equipped units during the operation had more to do with better tactics and training of the enemy than superiority of enemy tanks in the North African campaign, the operation revealed that the M3 had several technical faults. Mentioned in the British complaints were the 37 mm gun, a limited range and poor internal layout. The two-man turret crew was a significant weakness, and some British units tried to fight with three-man turret crews. Crews liked the vehicle's high speed and mechanical reliability.
From the summer of 1942, when enough US medium tanks had been received, the British usually kept Stuarts out of tank-to-tank combat. M3s, M3A3s, and M5s continued in British service until the end of the war, but British armor units had a smaller proportion of these light tanks than US units. The Republic of China army also received the M3A3s tanks and some were later used in the fight against the Communist forces.
The other major Lend-Lease recipient of the M3, the Soviet Union, was even less happy with the tank, considering it undergunned, underarmored, likely to catch fire, and too sensitive to fuel quality. The narrow tracks were highly unsuited to operation in winter conditions, as they resulted in high ground pressures that sank the tank. However, the Stuart was superior to early-war Soviet light tanks such as the T-60, which were often underpowered and possessed even lighter armament than the Stuart. In 1943, the Red Army tried out the M5 and decided that the upgraded design wasn't much better than the M3. Being less desperate than in 1941, the Soviets turned down an American offer to supply the M5. M3s continued in Red Army service at least until 1944.
In US Army service, the M3 first saw combat in the Philippines. Two battalions, comprising the Provisional Tank Group fought in the Bataan peninsula campaign. In 1941, the US Army Chief of Staff, General George C. Marshall, directed that the army's new M3 Stuart light tanks, then just rolling off the assembly lines, were to have the highest priority in reinforcing General MacArthur's command in the Pacific. The activated Army National Guard 194th and 192nd Tank Battalions were each equipped with 54 of the newly manufactured M3 Stuart light tanks, along with 23 half-tracks per battalion. The federalized California Army Guard 194th Tank Battalion deployed from San Francisco on 8 September 1941, arriving in the Philippines on 26 September. That deployment was followed by the 192nd Tank Battalion, which had been training at Fort Knox, which reached Manila in November.
On 21 November 1941 the 192nd and 194th Tank Battalions were combined to form the Provisional Tank Group under the command of Colonel James R. N. Weaver. With the subsequent commencement of hostilities, and Japanese landings along the coastlines in December, the Provisional Tank Group was ordered to counterattackM3/M5 Stuart p. 13">Zaloga p. 13 the landing forces, and to cover the allied retreat towards the Bataan Peninsula.
On 22 December 1941, the 192nd Tank Battalion became the first American tank to engage enemy armor in tank to tank combat during World War II as they ran into Japanese tanks from the Imperial Japanese Army 4th Tank Regiment. The M3's of the 192nd Tank Battalion went up against the equally armed Type 95 light tank, which were armed with the 37mm cannon, but were equipped with diesel engines. The Type 95 light tank had been at the forefront of tank technology when it was fielded in 1935. Both the 192nd and the 194th Tank Battalions continued to skirmish with the 4th Tank Regiment, as they retreated towards Bataan. During the remaining struggle for Bataan, the two Tank Battalions tried to defend the beaches, the airfield, and provided support for the infantry, until 8 April 1942, when the 192nd and 194th received orders to prepare to destroy their M3s, however, Americans were not successful in destroying all of their tanks, as many of the M3 Stuarts were captured and used by the enemy during the war. When the Philippines were liberated in 1944/45, some of those captured M3 Stuart light tanks were taken back by US forces. The unit withdrew to the Bataan Peninsula as part of the general retreat, and ceased to exist on 9 April 1942 when the last surviving American and Philippine forces on the Bataan Peninsula surrendered.
When the American army joined the North African Campaign in late 1942, Stuart units still formed a large part of its armor strength.
After the disastrous Battle of the Kasserine Pass, the US quickly disbanded most of their light tank battalions and subordinated the Stuarts to medium tank battalions, performing the traditional cavalry missions of scouting and screening. For the rest of the war, most US tank battalions had three companies of M4 Shermans and one company of M3s or M5/M5A1s.
In the European theater, Allied light tanks had to be given cavalry and infantry fire support roles since their main cannon armament could not compete with heavier enemy AFVs. However, the Stuart was still effective in combat in the Pacific Theater, as Japanese tanks were both relatively rare and were generally much weaker than even Allied light tanks. Japanese infantrymen were poorly equipped with anti-tank weapons and tended to attack tanks using close-assault tactics. In this environment, the Stuart was only moderately more vulnerable than medium tanks. In addition, the poor terrain and roads common to the theatre were unsuitable for the much heavier M4 medium tanks, and so initially, only light armor could be deployed. Heavier M4s were eventually brought to overcome heavily entrenched positions, though the Stuart continued to serve in a combat capacity until the end of the war.
The US liquidated its Stuarts when it got sufficient numbers of M24 Chaffees, but the tank remained in service until the end of the war and well after. In addition to the United States, United Kingdom and Soviet Union, who were the primary users, it was also used by France and China.
M22 Locust
The Light Tank M22, also known as the Locust, began development in late 1941 in response to a request by the British military earlier in the year for an airmobile light tank which could be transported onto a battlefield by glider. The United States Ordnance Department was asked to produce this replacement, which in turn selected Marmon-Herrington to design and build a prototype airborne tank in May 1941. The prototype was designed so that it could be transported underneath a Douglas C-54 Skymaster transport aircraft, although it would also fit inside a General Aircraft Hamilcar glider.After a series of modifications were made to the initial prototype, production began in April 1943. It was significantly delayed, however, when several faults were found with the tank's design. Marmon-Herrington only began to produce significant numbers of the T9 in late 1943 and early 1944, and by then the design was considered to be obsolete; only 830 were built by the time production ended in February 1945. As a result, the Ordnance Department gave the tank the specification number M22 but no American combat units were equipped with it.
However, during 1943, the War Office believed that the tank would perform adequately despite its faults that came to light, so the tank was given the title of 'Locust' and 260 were shipped to Great Britain under the Lend-Lease Act. Seventeen Locusts were received by the 6th Airborne Armoured Reconnaissance Regiment in late 1943. Eight were eventually used during the airborne Operation Varsity in March 1945. The tanks did not perform well in action and Locusts were never used in action again during WWII.
M24 Chaffee
In April 1943 the government started work on the M24 Chaffee, designated Light Tank T24 as a replacement for the M3/M5 Stuart after the original replacement, the M7, was rejected in March. Every effort was made to keep the weight of the vehicle under 20 tons. The armor was kept light, and a lightweight 75 mm gun was developed. The design also featured wider tracks and torsion bar suspension. It had relatively low silhouette and a three-man turret. In mid-October the first pilot vehicle was delivered and production began in 1944 under the designation "Light Tank M24". 4,730 were produced by the time production was stopped in August 1945.The first thirty-four M24s reached Europe in November 1944 and were issued to the U.S. 2nd Cavalry Group in France. These were then issued to F Company, 2nd Cavalry Reconnaissance Battalion and F Company, 42nd Cavalry Reconnaissance Battalion which each received seventeen M24s. During the Battle of the Bulge in December 1944, these units and their new tanks were rushed to the southern sector; two of the M24s were detached to serve with the 740th Tank Battalion of the U.S. First Army.
The M24 started to enter widespread issue in December 1944 but they were slow in reaching the front-line combat units. By the end of the war many armored divisions were still mainly equipped with the M5. Some armored divisions did not receive their first M24s until the war was over.
Reports were generally positive. Crews liked the improved off-road performance and reliability, but were most appreciative of the 75 mm main gun, as a vast improvement over the 37 mm. The M24 was not up to the challenge of fighting tanks, but the bigger gun gave it a chance to defend itself when required. Regardless, its light armor still left it vulnerable.
The M24's contribution to winning the war was insignificant, as too few arrived too late to replace the M5s of the armored divisions, but the M24 saw extensive use in the Korean War.
In the Korean War, M24s were the initial US tanks directed to combat the North Korean T-34-85s. The occupation troops in Japan from which the tanks were drawn were inexperienced and under-equipped due to rapid demobilization after World War II. The M24 fared poorly against these better armed, better armored, and better crewed medium tanks, losing most of their number while inflicting only minor damage on the T-34 units.
Medium and heavy tanks
M3 Lee
The Medium Tank M3 replaced the M2 Medium tank and design commenced in July 1940, and the first "Lees" were operational in late 1941. Many were sent to the British where the tank was called the "General Lee", or "General Grant" depending whether they had US specification or British specification turrets respectively.The U.S. Army needed a good tank and coupled with Great Britain's demand for 3,650 medium tanks immediately, the Lee began production by late 1940. The M3 was well armed and armored for the period, but due to design flaws it was not satisfactory and was withdrawn from front line duty as soon as the M4 Sherman became available in large numbers — the British managed to use the M3 successfully against the Imperial Japanese Army in Burma until 1945.
When the U.S. entered the war, the M2 series medium tank design was obsolete with a 37 mm gun, 32 mm frontal armor, machine gun main armament and a very high silhouette. The Panzer III and Panzer IV's success in the French campaign led the U.S. Army to immediately order a new medium tank armed with a 75 mm gun in a turret. This would be the M4 Sherman. However, until the Sherman was in production, an interim design with a 75 mm gun was urgently needed.
The M3 was the solution. The design was unusual because the main weapon, a larger caliber, low-velocity 75 mm gun, was mounted in an offset sponson within the hull. This gave the gun a limited traverse. A small turret with a lighter, high-velocity 37 mm gun sat on the tall hull. An even smaller cupola on top of the turret held a machine gun. The British ordered the M3 when they were refused permission to have their tank designs made by American factories. British experts had viewed the mock-up in 1940 and identified several flaws — the high profile, the hull mounted gun, radio in the hull, smooth tracks, the amount of armor with insufficient attention to splash-proofing the joints. The British agreed to order 1,250 M3, to be modified to their requirements - the order was subsequently increased with the expectation that when a superior tank was available it could replace part of the order. Contracts were arranged with three U.S. companies, but the total cost was approximately 240 million US dollars. This sum was all of the British funds in the US and it took the Lend-Lease act to solve the financial problems.
The prototype was completed in March 1941 and production models followed with the first British specification tanks in July. The British cast turret included a bustle at the back for the Wireless Set No. 19 radio. It had thicker armour than the U.S. one and removed the U.S. cupola for a simple hatch. Both U.S. and British tanks had thicker armor than first planned. The British design required one fewer crew member than the US version due to the radio in the turret. The U.S. eventually eliminated the full-time radio operator, assigning the task to the driver. The British realized that to meet their requirement for tanks both types would be needed.
The U.S. military utilized the "M" letter to designate nearly all of their equipment. When the British Army received their new M3 medium tanks from the US, confusion immediately set in, as the M3 medium tank and the M3 light tank were identically named. The British Army began naming their American tanks, although the U.S. Army never used those terms until after the war. The M3 tanks with the new turret and radio setup received the name "General Grant", while the original M3s were called "General Lee", or more usually just "Grant" and "Lee". The M3 brought much-needed firepower to British forces in the African desert campaign.
The 75 mm was operated by a gunner and a loader. The 75 mm gun used an M1 periscope, with an integral telescope, which was mounted on top of the sponson for sighting. The periscope rotated with the gun. The sight was marked from zero to with vertical markings to aid deflection shooting at a moving target. The gunner laid the gun on target through geared handwheels for traverse and elevation.
The 37 mm was aimed through the M2 periscope, though this was mounted in the mantlet to the side of the gun. It also sighted the coaxial machine gun. Two range scales were provided: 0- for the 37 mm and 0- for the machine gun.
, November 23, 1942
Of the 6,258 M3s produced by the U.S., 2,855 M3s were supplied to the British Army, and about 1,368 to the Soviet Union. Consequently, one of the American M3 medium tank's first actions during the war was in 1942, during the North African Campaign. British Lees and Grants were in action against Rommel's forces at the disastrous Battle of Gazala on 27 May that year. They continued to serve in North Africa until the end of that campaign. A regiment of M3 Mediums was also used by the U.S. 1st Armored Division in North Africa. In the North African campaign, the M3 was generally appreciated for its mechanical reliability, good armor and heavy firepower.
In all three areas, it outclassed the available British tanks and was able to fight German tanks and towed anti-tank guns. The tall silhouette and low, hull-mounted 75 mm were severe tactical drawbacks, since they prevented the tank from fighting from hull-down firing positions. The use of riveted armor led to a problem called "spalling", whereby the impact of enemy shells would cause the rivets to break off and become projectiles inside the tank. Later models were welded to eliminate this problem. The M3 was replaced by the M4 Sherman as soon as these were available, though several M3s saw limited action in the battle for Normandy as armored recovery vehicles with dummy guns.
M4 Sherman tank
The M4 was the best known and most used American tank of World War II. Christened "Sherman" by the British, it was named for the famous US Civil War General, William Tecumseh Sherman. The M4 Sherman was a medium tank that proved itself in the Allied operations in North Africa, Europe and the Pacific theaters of war in World War II. The Sherman was a relatively inexpensive, easy to maintain and produce combat system. Similar to production efforts on the part of the Soviet Union with their T-34 tank system, the M4 Sherman was the same class of mass-produced tank weapon.The new design was put into action beginning on August 31, 1940. This medium tank would have to mount a 75 mm main gun armament into a fully-traversable turret. The new tank would also have to incorporate the engine, transmission, tracks and suspension systems of the M3 Lee medium tanks in an effort to ease production and save time. This new medium tank would also have to reduce the crew from six to five and feature improved armor allocation without increasing the vehicle's overall weight.
The design appeared as the T6 pilot model: it proved acceptable to US Army officials and production was ordered for the new "M4" on September 5, 1941. Before production on the M4 ramped up, however, the M4 design was further revised to include a 12.7 mm heavy-barrel Browning machine gun on the turret for anti-aircraft defense. A.30 caliber machine gun was then added to the upper hull bow plate.
The Army had seven main sub-designations for M4 variants during production: M4, M4A1, M4A2, M4A3, M4A4, M4A5, and M4A6. These designations did not necessarily indicate linear improvement: for example, A4 was not meant to indicate it was better than the A3. These sub-types indicated standardized production variations, which were in fact often manufactured concurrently at different locations. The sub-types differed mainly in engines, although the M4A1 differed from the M4 by its fully cast upper hull; the M4A4 had a longer engine system that required a longer hull, a longer suspension system, and more track blocks; M4A5 was an administrative placeholder for Canadian production; and the M4A6 had an elongated chassis, but fewer than 100 of these were produced.
One main problem for the Sherman design, in its various forms, was the heavier guns on the German tanks coming onto the battlefield in the latter half of the war, especially the Tiger and Panther tanks. The German Tiger I tank was armed with powerful 88 mm gun that made it a very dangerous opponent for any Allied tank.
While most Shermans ran on gasoline, the M4A2 and M4A6 had diesel engines: the M4A2 with a pair of GMC 6-71 straight six engines, the M4A6 a Caterpillar RD1820 radial. These, plus the M4A4, which used the Chrysler A57 multibank engine, were mostly supplied to Allied countries under Lend-Lease. "M4" can refer specifically to the initial sub-type with its Continental radial engine, or generically to the entire family of seven Sherman sub-types, depending on context.
Many details of production, shape, strength and performance improved throughout production, without a change to the tank's basic model number: more durable suspension units, safer "wet" ammunition stowage, and stronger armor arrangements, such as the M4 Composite, which had a cast front hull section mated to a welded rear hull. British nomenclature differed from that employed by the U.S. While the M4 Sherman tank also went into service with US allies it was also used in conflicts beyond World War II.
A 24-volt electrical system was used in the M4.
Early Shermans mounted a 75 mm medium-velocity general-purpose gun. Although Ordnance began work on the Medium Tank T20 as a Sherman replacement, ultimately the Army decided to minimize production disruption by incorporating elements of other tank designs into the Sherman. Later M4A1, M4A2, and M4A3 models received the larger T23 turret with a high-velocity 76 mm M1 gun, which reduced the number of HE and smoke rounds carried and increased the number of anti-tank rounds.
Later, the M4 and M4A3 were factory-produced with a 105 mm howitzer and a new distinctive mantlet in the original turret. The first standard-production 76 mm gun Sherman was an M4A1, accepted in January 1944, and the first standard-production 105 mm howitzer Sherman was an M4 accepted in February 1944.
In June–July 1944, the Army accepted a limited run of 254 M4A3E2 Jumbo Shermans, which had very thick armor, and the 75 mm gun in a new, heavier T23-style turret, in order to assault fortifications at Normandy Beach. Some armor points exceeded 7 inches in effective thickness. Later some were upgraded with the 76.2 mm gun. The M4A3 was the first to be factory-produced with the horizontal volute spring suspension with wider tracks to distribute weight; the smooth ride of the HVSS with its experimental E8 designation led to the nickname "Easy Eight" for Shermans so equipped. Some E8s were equipped with the M101 howitzer.
Both the Americans and the British developed a wide array of special attachments for the Sherman; few saw combat, and most remained experimental. Those that saw action included the bulldozer blade for the Sherman dozer tanks, Duplex Drive for "swimming" Sherman tanks, R3 flamethrower for Zippo flame tanks, and both the T34 60-tube Calliope 4.5" rocket launcher and T40 Whizbang 7.2" rocket launcher for the Sherman turret. The British variants were among "Hobart's Funnies" of the 79th Armoured Division.
M6 Heavy Tank
The M6 heavy tank was a heavy tank built off of the similarly designed multi-turreted T1, armed with a 76.2 mm gun, a co-axial 37 mm gun, two.50 cal and two.30 Browning machine guns, two in the hull and one on top of the turret. An order of 50 was placed and prototype vehicles saw trials but by the time it was ready for full-scale production the Army did not see any advantages over the M4 Sherman and planned production was cut from 5000 to 40. The M6 was declared obsolete in 1944 but was used in propaganda efforts in the States.T14 Heavy Tank
The T14 Heavy Tank was a joint US-British project to produce a heavy tank that could equip both armies, armed either with the American 75 mm or British 57 mm 6-pounder gun. The British ordered several thousand in 1942 but by time the pilot was tested in 1944 they no longer had a need for it.M26 Pershing
The M26 Pershing Heavy Tank came into service in 1945 under the designation of M26 Heavy Tank with the name "Pershing" after the founder of the US Tank Corps in World War I, General John J Pershing. It saw limited combat in Germany where it held its own with the German PzKpfw VI and V tanks, which quite easily outmatched the M4 Sherman that the Pershing was replacing. The tank was a large improvement over the M4. It was developed from the T20 Medium Tank, a faster version of the T14 heavy tank.The M26 Pershing Heavy Tank had heavier armor, a more powerful gun, and improved torsion bar suspension compared to the Sherman. The main armament of the M26 Pershing was its 90 mm gun. Secondary.30 cal. machine guns were mounted co-axially in the turret and in the bow. A.50 cal. machine gun was mounted on top of the turret.
One M26 had extra armor welded on, had an improved version of the 90 mm gun mounted on the turret, and additional armor protection had been installed. Nicknamed "Super Pershing" it was comparable to the German Tiger II in firepower and protection and was one of only two deployed to Europe during World War II. It saw combat in mid-1945.
A total of 2,222 M26 Pershing tanks were produced, beginning in November 1944, only 20 of which saw combat in Europe during World War II. The tank was reclassified as a medium tank in May 1946, and while it didn't have time to make any real impact in the Second World War, it served with distinction in the Korean War alongside the M4A3E8 Sherman. In combat it was, unlike the M4 Sherman, fairly equal in firepower and protection to both the Tiger I and Panther tanks and similarly to them underpowered and mechanically unreliable.
Tank destroyers and assault guns
M18 Hellcat
The M18 Hellcat was a tank destroyer, used in the Italian, European, and Pacific theatres, and in the Korean War. It was the fastest armored vehicle in the American defense inventory of the 20th century, until the turboshaft-powered M1 Abrams main battle tank appeared decades later. The speed was attained by keeping armor to a minimum, no more than one inch thick and roofless, open-top turrets and by powering the relatively small vehicle with a radial engine originally designed for aircraft usage.M10 GMC
M4 Sherman-based M10 tank destroyerM36 GMC
Together with the M10 and M18, the 90 mm gun-armed M36 tank destroyer, provided American and Allied forces with a respectable mobile anti-tank capability against the newer German armored types.Howitzer Motor Carriage M8
The Howitzer Motor Carriage M8 was a self-propelled howitzer used for close support. It saw use on the western and Italian fronts, as well as in the Pacific. The turret had a 75mm howitzer and was mounted on an M5 Stuart hull. It also had an M2 Browning machine gun. It went 36 mph on roads, had 9.5–44 mm of armor, and had a crew of four. It was very effective against bunkers and other stationary enemy positions. It later saw use in the First Indochina War and the Algerian War. Some self-propelled artillery and self-propelled mortar vehicles were used in the direct fire role, but the M8 and the 105 mm howitzer-armed Shermans were the only vehicles dedicated for the use.Korean War and Cold War
Korean Conflict
Light tanks
M24 Chaffee
The M24 Chaffee was intended to replace the aging and obsolete Light Tank M5, which was used in supplementary roles. Crews liked the improved off-road performance and reliability, but were most appreciative of the 75 mm main gun, which was a vast improvement over the 37 mm. The M24's light armor made it vulnerable to enemy tanks, anti-tank guns, and hand-held anti-tank weapons.In the Korean Conflict, M24s were the initial U.S. tanks directed to combat the North Korean T-34-85s. The occupation troops in Japan from which the tanks were drawn were inexperienced and under-equipped due to rapid demobilization after World War II. The M24 fared poorly against these better armed, better armored, and better crewed medium tanks, losing most of their number while inflicting only minor damage on the T-34 units. Managing a fighting withdrawal, they ended up as artillery in the Pusan Perimeter; in August reinforcements from the US and the Commonwealth brought heavier tanks that could easily dispatch the T-34s. M24s were more successful later in the war in their reconnaissance role, supported by heavier, more capable tanks such as the M4 Sherman, M26 Pershing, and M46 Patton.
M41 Walker Bulldog
The development of the T37 began in 1947 to replace the M24 Chaffee. The vehicle was designed to be air-transportable, and with heavier firepower, provided by an advanced 76 mm gun. In 1949, with the adoption of a less ambitious rangefinder, the project's designation was changed to M41. Production started in 1951 at Cadillac's Cleveland Tank Plant, and by 1953 the new tank completely replaced the M24 in the United States Army. It was later designated the M41 Walker Bulldog. The M41 was agile and well armed. On the other hand, it was noisy, fuel-hungry and heavy enough to cause problems with air transport.The Walker Bulldog saw limited combat with the U.S. Army during the Korean Conflict, but for the most part, the conflict served as a testing ground to work out the tank's deficiencies, especially with its rangefinder. At the time, it was designated as the T-41, and was rushed to the battlefield even before its first test run. This was due to the fact that the North Koreans were supplied with Soviet T-34 tanks, which were superior to the M24.
It also was used in nearby Japan, by 1961, 150 were delivered to the Japan Ground Self-Defense Force to supplement their Type 61 medium tanks.
It was also used in the Bay of Pigs conflict by the Brigade 2506, with the M41 Walker Bulldog tanks going against the Cuban T-34-85 tanks, with five T-34-85 tanks destroyed and others severely damaged.
Medium tanks
M4A3
The M4A3 was the last type of Sherman in U.S. service. It was roughly equal to the enemy T-34-85s and they could destroy each other at normal combat ranges. Later in the war, they were only used for artillery and reserves.M26 Pershing
The M26 Pershing was named after General John J. Pershing who led the American Expeditionary Force in Europe in World War I, it was designed and came out at the end of World War II and was used in the Korean Conflict. In May 1946, due to changing conceptions of the U.S. Army's tank needs, the M26 was reclassified as a medium tank. Designed as a heavy tank, the Pershing was a significant upgrade from the M4 Sherman in terms of firepower with its 90 mm gun and protection.On the other hand, its mobility was unsatisfactory for a medium tank and its transmission was somewhat unreliable. In 1948, the M26E2 version was developed with a new powerpack. Eventually the new version was redesignated the M46 General Patton and 1,160 M26s were rebuilt to this new standard so the later M48 Patton and M60 Patton, which saw service in later Vietnam and Mideast conflicts were evolutionary redesigns of the original layout set down by the Pershing.
M46 Patton
The mobility of the M26 Pershing was deemed unsatisfactory for a medium tank, as it added 10 tons of weight but used the same engine that powered the much lighter M4 Sherman.Work began in 1948 on replacing the power plant in the M26 Pershing, with a more powerful engine and more reliable transmission. The Continental AV1790-3 was chosen which was capable of more than 800 hp compared to the previous engine in the M26 Pershing which was rated for only 500 hp, and was coupled with the cross-drive transmission Allison CD-850-1. Modifications continued to accumulate, and eventually the Bureau of Ordnance decided that the tank needed its own unique designation. When the rebuild began in November, 1949, the upgraded M26 received a new power plant and a main gun with bore evacuator, and the M46 Patton designation. Less than a thousand were upgraded to M46 standard.
supported by M46 Patton tank.
The M46 Patton became a completely upgraded and modernized version of the M26 Pershing and total of 1,168 M46 tanks, were manufactured between 1949 and 1951. It was needed in Korea and on 8 August 1950 the first M46 Pattons landed in South Korea. The tank proved superior to the much lighter North Korean T-34-85, which were encountered in relatively small numbers. By the end of 1950, 200 M46 Pattons had been fielded, forming about 15% of US tank strength in Korea; the balance of 1,326 tanks shipped to Korea during 1950 included 679 M4A3 Shermans, 309 M26 Pershings, and 138 M24 Chaffee light tanks.
The M46 Patton was slower compared to other medium tank counterparts, but its maneuverability and powerful 90 mm gun made it a formidable weapon especially in the Korean Conflict.
Subsequent shipments of M46 and M46A1 Pattons allowed all remaining M26 Pershings to be withdrawn during 1951, and most Sherman equipped units were also reequipped.
Post-Korean War
Medium tanks
M47 Patton
The M47 Patton was intended to replace the M46 Patton and M4 Sherman tanks. It had a 90 mm gun and a crew of 5. Despite it being the primary tank of the US it never saw combat while in US service.M48 Patton
In early 1951, the U.S. initiated the design of the M48 Patton, designated the T-48 with a 90 mm cannon. The T48 featured a new turret, new redesigned hull and an improved suspension. The hull machine gunner position was removed, reducing the crew to 4. On 2 April 1953, the Ordnance Technical Committee Minutes, standardized the last of the Patton series tanks as the M48 Patton.Nearly 12,000 M48s were built from 1952 to 1959. The early designs, up to the M48A2, were powered by a gasoline 12-cylinder engine which was coupled with an auxiliary 8-cylinder engine. The gas engines gave the tank a short operating range and were prone to catching fire when hit. This version was considered unreliable.
T95 Medium Tank
The T95 was an American series of prototype medium tanks developed from 1955 to 1959. These tanks used many advanced or unusual features, such as siliceous-cored armor, the APFSDS-firing 90 mm T208 smoothbore gun in a rigid mounting without a recoil system, a new transmission, and the OPTAC fire-control system, which incorporated the T53 Optical Tracking, Acquisition and Ranging system, emitted pulsed beams of intense but incoherent infrared light.Heavy tanks
M103 heavy tank
The M103 was manufactured at the Detroit Arsenal Tank Plant and the first units were accepted in 1957.The M103 was designed to counter Soviet heavies. Its long-ranged 120 mm cannon was designed to hit enemy tanks at extreme distances, but it was never used in combat. Of the 300 M103s built, most went to the Marines. The tank was relatively underpowered and the drive systems were fragile.
The turret of the M103 was larger than that of the M48 or the M60 to make room for the huge 120 mm gun and the two loaders assigned to it, in addition to the gunner and the commander. The driver sat in the hull. The gun was capable of elevation from +15 to -8 degrees.
While the US Army deactivated its heavy armor units with the reception of the new M60 series main battle tanks in 1960, the remaining M103s stayed within the US Marine Corps inventory until they began receiving the M60 series MBT. With the disappearance of the heavy tank from US forces came the full acceptance of the main battle tank in 1960 in the U.S. Army, and 1973 in the U.S. Marine Corps.
Vietnam
Light tanks
T92 Light Tank
The T92 Light Tank was an innovative American light tank developed in the 1950s by Aircraft Armaments. It was designed as an airborne/airdropped replacement for the much heavier M41 Walker Bulldog. The main gun was a conventional 76 mm cannon with a very low profile turret. Little more was exposed than the main gun and two crew cupolas which allowed 50 caliber and 30 caliber machine guns to fire buttoned up. The engine is moved to the front, which increases protection, and a rear access door provided an escape hatch and protection while reloading. Study of the Soviet PT-76 led to a new swimming requirement for Light tanks, for which the design could not be modified. The T-92 would be passed over and the M551 Sheridan was eventually adopted instead. The T92 was never accepted into service.M551 Sheridan
The design of the M551 Sheridan was initiated when the replacement for the M41, the T92 Light Tank, was canceled.The need for even lighter weight than the T-92 presented the design with a particularly difficult problem; guns capable of defeating modern tanks at reasonable ranges were so large that they demanded a large vehicle to carry them, so large that they couldn't be used as a "light" tank. The use of HEAT rounds instead of conventional penetrating ammunition could address this, but HEAT rounds work better at larger calibers. Gun weight is typically the product of caliber and muzzle velocity, so in the case of the XM551 they sacrificed the muzzle velocity, producing the low-velocity but relatively large-caliber 152 mm M81. HEAT rounds fired by the M81 could defeat any contemporary tank at shorter ranges, but its low velocity made it difficult to use at longer ranges, especially against moving targets. The large low-velocity gun was also ideal for infantry support, where higher performance anti-tank guns would often fire right through soft targets and their small-caliber guns left little room for explosive filler. The M81 would thus be ideal for both direct fire support as well as short-distance anti-tank engagements.
The only niche where the M81 was not ideal was the medium and long-range anti-tank engagement. The muzzle velocity was so low that a HEAT round fired at longer ranges would have to be "lofted", making aiming difficult, and the flight time would be so long that a moving target would be very difficult to hit. However, it appeared there was a solution to this problem by equipping the tank with gun-fired anti-tank missiles. For longer range engagements a missile would be fired instead of a HEAT round, and although its velocity would also be relatively slow, the guidance system would make a hit highly likely anyway. A number of vehicles mounting only ATGM's, or alternately recoilless rifles like the US's own Ontos tank were already in service, but typically these vehicles had limited firepower in the infantry support role, or in the case of Ontos could not be reloaded from within the vehicle. The XM551 appeared to offer the best of both worlds; for infantry support the large calibre gun allowed it to fire full-sized artillery rounds and canister shot, while also giving it reasonable short-range anti-tank performance from the same gun. Although the Shillelagh missile was considered a risky project, if it worked the XM551 would be able to deal with even the largest tanks at extreme ranges.
The vehicle designed to mount the gun had a steel turret and aluminum hull. It was powered by a large diesel engine. The M551 thus had excellent mobility, able to run at speeds up to 45 mph, which at that time was unheard of for a tracked vehicle. Swimming capability was provided by a flotation screen. Production started on late July 1966, and entered service in June 1967. More than 1,600 M551s were built between 1966 and 1970. Total cost of the M551 program was $1.3 billion.
The vehicle proved to be very noisy and unreliable under combat conditions. The armor was thin enough that it could be penetrated even by heavy machine gun rounds as well as being highly vulnerable to mines.
Firing the gun would often adversely affect the delicate electronics, which were at the early stages of transitioning to solid state, so the missile and guidance system was omitted from vehicles deployed to Vietnam. Indeed, this missile would end up almost never being fired in anger, despite the production of 88,000 of the expensive missiles. The gun had problems with cracks developing near the breech after repeated firing. Most field units were modified to help address the problem and the modified M81E1 was introduced with a shallower slot, along with a matching modification to the missile, that cured the problem. The gun also has been criticized for having too much recoil for the vehicle weight, the second and even third road wheels coming clear off the ground when the main gun fired.
The Sheridan saw extensive action in the Vietnam War, being assigned to nearly all armored cavalry squadrons in the country. In 1969, armored cavalry units began replacing their M48 Patton tanks.
.
The battle reports from the troops were sometimes glowing, while the reports higher up the chain of command were often negative. A 1969 evaluation of the vehicles found the M551 was employed in reconnaissance, night patrol and road clearing, accumulating 39,455 road miles and 520 combat missions, with a ready rate of 81.3 percent. Despite vulnerability to rockets and mines, it was judged worth applying modifications and equip all cavalry squadrons with the Sheridan.
The Sheridan was much appreciated by the infantry who were desperate for direct-fire support, which generally served in combination with ACAVs as armored cavalry units consisted of both M113s and M551s as part of their TO&E. Armor units consisted solely of tanks and Mechanized Infantry units consisted solely of M113s. In this role the real problem with the Sheridan was its limited ammunition load of only 20 rounds and 8 missiles.
A common field-modification was to mount a large steel shield, known as an "ACAV set", around the commander's 50-cal. gun, allowing it to be fired with some level of protection. The driver has an unusual rotating hatch which has vision blocks when rotated forward. Included with the set was an extra layer of steel belly armor which was bolted onto the vehicle's bottom, although only covering from the front to halfway to the end, possibly due to weight reasons.
A standard modification made during the mid-70's was the addition of the "Cereal Bowl" commander's cupola. This mod came about due to the broken rib effect that occurred when the Sheridan fired conventional rounds, the recoil would pitch the TC against the armor plating resulting in cracked ribs.
Medium Tanks
M48 Patton
The M48s saw extensive action during the Vietnam War; over 600 Pattons would be deployed with US Forces during the war. The initial M48s landed with the US Marines in 1965. Remaining Pattons deployed to South Vietnam were in three U.S. Army battalions, the 1-77th Armor near the DMZ, the 1-69th Armor in the Central Highlands, and the 2-34th Armor near the Mekong Delta. Each battalion consisted of approximately fifty seven tanks. M48s were also used by Armored Cavalry Squadrons in Vietnam, until replaced by M551 Sheridan tanks. The M67A1 flamethrower tank was an M48 variant used in Vietnam.When US forces commenced redeployment operations, many of the M48A3 Pattons were turned over to the Army of the Republic of Vietnam forces, in particular creating the ARVN 20th Tank Regiment; which supplemented their M41 Walker Bulldog units. During the North Vietnamese Army Easter Offensive in 1972, tank clashes between NVA T-54/PT-76 and ARVN M48/M41 units became commonplace, but on 23 April 1972, tankers of the 20th Tank Regiment were attacked by an NVA infantry-tank team, which was equipped with the new 9M14M Malyutka wire guided anti-tank missile. During this battle, one M48A3 Patton tank and one M113 Armored Cavalry Assault Vehicle were destroyed, becoming the first losses to the Sagger missile; losses that would echo on an even larger scale a year later during the Yom Kippur War in the Middle East in 1973.
The M48s performed admirably in Vietnam in the infantry-support role. However, there were few actual tank versus tank battles. The M48s provided adequate protection for its crew from small arms, mines, and rocket-propelled grenades.
In the mid-1970s, the M48A5 upgrade was developed to allow the vehicle to carry the heavier 105 mm gun. This was designed to bring the M48s up to speed with the M60 tanks then in regular use. Most of the M48s were placed into service with reserve units by this time. By the mid-1990s, the M48s were phased out.
Main battle tanks
M60 Patton
The M60 Patton was designed as a replacement for the M48 Patton and is based on its chassis.M60
In 1957, plans were laid in the US for a tank with a 105 mm main gun and a redesigned hull offering better armor protection.The resulting M60 largely resembled the M48 it was based on, but has significant differences. The M60 mounted a bore evacuated 105 mm main gun, had a hull with a straight front slope whereas the M48's hull was rounded, had three support rollers per side to the M48's five, and had road wheels constructed from aluminum rather than steel.
The hull of the M60 was a single piece steel casting divided into three compartments, with the driver in front, fighting compartment in the middle and engine at the rear. The driver looked through three M27 day periscopes, one of which could be replaced by a night vision periscope. Initially, the M60 had essentially the same turret shape as the M48, but this was subsequently replaced with a distinctive "needlenose" design that minimized frontal cross-section to enemy fire.
The M60 was the last U.S. main battle tank to utilize homogeneous steel armor for protection. It was also the last to feature either the M60 machine gun or an escape hatch under the hull.
Originally designated the M68, the new vehicle was put into production in 1959, reclassified as the M60, and entered service in 1960. Over 15,000 M60s were constructed.
M60A1
In 1963, the M60 was upgraded to the M60A1. This new variant, which stayed in production until 1980, featured a larger, better-shaped turret and improvements to the armor protection and shock absorbers. The M60A1 was also equipped with a stabilization system for the main gun. However, the M60A1 was still not able to fire on the move, as the system only kept the gun pointed in the same general direction while the tank was traveling cross country. It did however enable the coaxial machine gun to be brought to bear while moving.Post-Vietnam
Light tanks
M551 Sheridan
The Army began to phase out the Sheridan in 1978, although at the time there was no real replacement. Nevertheless, the 82nd Airborne were able to keep them on until 1996. The Sheridan was the only air-deployable tank in the inventory, and as an elite force they had considerably more "pull" than general infantry and armor units who were forced to get rid of them. Their units were later upgraded to the M551A1 model, including a thermal sighting system for the commander and gunner.delivering an M551 Sheridan tank using LAPES.
The Sheridan's only air drop in combat occurred during Operation Just Cause in Panama in 1989, when fourteen M551's were deployed; four were transported by C-5 Galaxies and ten were dropped by air, but two Sheridans were destroyed upon landing. The Sheridans' performance received mixed reviews. They were lauded by their operators and some commanders as providing firepower in situations which needed to destroy hard targets. However, the Sheridans' employment of only HEAT rounds limited their effectiveness against reinforced concrete construction.
51 Sheridans were deployed in the Gulf War as some of the first tanks sent. They would not be very effective against the Russian-built T-72s. Their role was limited by age and light armor to reconnaissance, possibly 6 or fewer Shillelagh missiles were fired at Iraqi bunkers. These few missiles, less than a half-dozen of the 88,000 produced, were the only Shillelagh fired in a combat environment.
Several attempts to upgun or replace the Sheridan have been made, but none were successful. Several experimental versions of the Sheridan mounting a new turret carrying a 105 mm gun were made, but the resulting recoil was too great. Several possible replacements for the M551 were tested as a part of the XM8 Armored Gun System and expeditionary tank efforts of the early and late 1980s respectively, but none of these entered service. The Stryker Mobile Gun System has replaced the light tank role of the United States.
Main battle tanks
M60A2
The M60A2, nicknamed the "Starship" due to its Space Age technology, featured an entirely new low-profile turret with a commander's machine-gun cupola on top, giving the commander a good view and field of fire while under armor but spoiling the low profile. It also featured a 152 mm cannon, which fired conventional rounds as well as guided missiles.The M60A2 proved a disappointment, though technical advancements would pave the way for future tanks. The Shillelagh/M60A2 system was phased out from active units by 1981, and the turrets scrapped. Most of the M60A2 tanks were rebuilt as M60A3.
M60A3
The development of the M60A2 with a new turret fitted with a 152mm gun was stopped and in 1978, work began on the M60A3 variant. It featured a number of technological enhancements, including smoke dischargers, a new rangefinder, and M21 ballistic computer, and a turret stabilization system. In addition, it reverted to the M68A1 105 mm cannon. All active American Army M60s eventually underwent the conversion to the A3 model. The M60A3 main battle tanks of the US Marines were deployed in Operation Desert Storm in 1991 during the Gulf Crisis.The M60A3 was phased out of US service in 1997 and was replaced by the M1 Abrams main battle tank.
MBT-70
The MBT-70 was an American–West German joint project to develop a new main battle tank during the 1960s.The MBT-70 was developed by the United States and West Germany in the context of the Cold War, intended to counter the new generation of Warsaw Pact tanks developed by the Soviet Union. The new tank was to be equipped with a number of advanced features such as newly developed "kneeling" hydropneumatic suspension and housing the entire crew in the large turret, and was armed with a 152mm XM150 gun/launcher, which could use conventional ammunition and the Shillelagh missile for long range combat.
By the late 1960s, the development of the MBT-70 was well over budget and affected by design issues. West Germany withdrew from the project due to costs and a new difference in requirements. The United States continued development of the MBT-70 until 1971 when the program was finally cancelled. West Germany independently developed the Leopard 2 as its new main battle tank.
M1 Abrams
The M1 Abrams came from the diverted funds from the over budget and impractical MBT-70 and XM815 projects.Prototypes were delivered in 1976 by Chrysler Defense and General Motors armed with a license-built 105 mm rifled cannon. The Chrysler Defense design was selected for development as the M1. In 1979, General Dynamics Land Systems Division purchased Chrysler Defense. The M1 was the first of its kind. It featured a low profile turret and for the first time ever on a tank, composite chobham armor. Despite all these advances, the Abrams still retained the 4-man crew of the M60 Patton as the autoloader was considered unproven and risky.
Over 3,200 M1 Abrams were produced and first entered US Army service in 1980.
About 6,000 upgraded M1A1 Abrams were produced and used a 120 mm smoothbore cannon, improved armor, and a CBRN protection system.
As the Abrams entered service in the 1980s, they would operate alongside M60A3 Patton. These exercises usually took place in Western Europe, especially West Germany, but also in some other countries like South Korea. During such training, Abrams crews honed their skills for use against the Soviet Union. However, by 1991 the USSR had collapsed and the Abrams would have its trial by fire in the Middle East.
Since the Cold War the U.S. has moved away almost completely from using light tanks; instead supplementing these with heavily armed armored cars. The M60A3 Patton continued in service with the Marines and saw action in the Gulf War.
Iraq Conflict
Gulf War
M60 Patton
The M60A1 tanks of the U.S. Marines saw action during Operation Desert Storm in 1991, opposing Iraqi armor which included the T-54/T-59, T-55, T-62, Type 69, and T-72. The M60A1s were fitted with add-on explosive reactive armor packages and supported the drive into Kuwait City where they were involved in a two-day tank battle at the Kuwait airport with the loss of only one vehicle and no crew. They saw service with the United States Marine Corps, and the Saudi Arabian Army.M1 Abrams
When the Abrams entered service in the 1980s, they operated alongside M60A3 within the United States military, and with other NATO tanks in numerous Cold War exercises. These exercises usually took place in Western Europe, especially West Germany, but also in some other countries like South Korea. During such training exercises, Abrams' crews honed their skills for use against Soviet soldiers, equipment and vehicles. However, by 1991 the USSR had collapsed and the Abrams had not been in any combat.The Abrams remained untested in combat until the Gulf War in 1991. A total of 1,848 M1A1s were deployed to Saudi Arabia. The M1A1 was superior to Iraq's Soviet-era T-55 and T-62 tanks, as well as Iraqi assembled Russian T-72s, and locally produced copies. The T-72s like most Soviet export designs lacked night vision systems and then-modern rangefinders, though they did have some night fighting tanks with older active infrared systems or floodlights—just not the latest starlight scopes and passive infrared scopes as on the Abrams. Only 23 M1A1s were taken out of service in the Gulf and one of these losses resulted in crew deaths from Iraqi fire. Some others took minor combat damage, with little effect on their operational readiness. Very few Abrams tanks were hit by enemy fire, and there was only one fatality, along with a handful of wounded as a result.
Interwar upgrades
The M1A2 was a further improvement, with a commander's independent thermal viewer and weapon station, position navigation equipment, digital data bus and a radio interface unit.Further upgrades included depleted uranium armor for all variants, a system overhaul that returns all A1s to like-new condition, a digital enhancement package for the A1, a commonality program to standardize parts between the U.S. Army and the Marine Corps and an electronic upgrade for the A2.
During Operations Desert Shield and Desert Storm and for Bosnia, some M1A1s were modified with armor upgrades.
Afghanistan/Iraq Wars
M1 Abrams
Further combat was seen during 2003 in Iraq and Afghanistan. As of March 2005, approximately 80 Abrams tanks were forced out of action by enemy attacks.The campaign in Iraq saw very similar performance from the tank from the Persian Gulf war, with no Abrams crew member being lost to hostile fire during the invasion of Iraq, although several tank crew members were later killed by snipers and roadside bombs during the occupation that followed. Abandoned Abrams were purposely destroyed by friendly fire to prevent recovery of vehicle or technology. Damage by 25 mm AP-DU, anti-armor RPG fire and 12.7 mm rounds was encountered. But on no occasion did anti-tank guided weapons or anti-tank mines strike the US MBTs.
The most lopsided achievement of the M1A1s was the destruction of seven T-72 Lion of Babylon tanks in a point-blank skirmish near Mahmoudiyah, about south of Baghdad, with no losses for the American side. However, on October 29, 2003, two soldiers were killed and a third wounded when their tank was disabled by an anti-tank mine, which was combined with other explosives to increase its effect. The massive explosion beneath the tank knocked off the turret. This marked the first time deaths resulted from a hostile-fire assault on the M1 tank from enemy forces.
The M1A3 Abrams is in the early design period with the U.S. Army. The Army aims to build prototypes by 2014 and to begin to field the first combat-ready M1A3s by 2017. The Army anticipates that the Abrams may remain in U.S. service until 2050.
The U.S. Army's Future Combat Systems' XM1202 was to replace the Abrams and was in development when funding for the program was cut from the DoD's budget. The U.S. Army's BCT Ground Combat Vehicle Program may have also produced a replacement for the Abrams were it not cancelled in 2014.