Strain partitioning


Strain partitioning is commonly referred to as a deformation process in which the total strain experienced on a rock, area, or region, is heterogeneously distributed in terms of the strain intensity and strain type. This process is observed on a range of scales spanning from the grain – crystal scale to the plate – lithospheric scale, and occurs in both the brittle and plastic deformation regimes. The manner and intensity by which strain is distributed are controlled by a number of factors listed below.

Influencing factors

All four of these factors below may individually or in combination contribute toward the distribution of strain. Therefore, each of these factors must be taken into consideration when analyzing how and why strain is partitioned:
  1. Anisotropy such as preexisting structures, compositional layering, or cleavage planes. Isotropic lines "separate mutually orthogonal principle trajectories on each side. In a plane-strain field, the strain is zero at isotropic points and lines, and they can be termed neutral points and neutral lines."
  2. Rheology
  3. Boundary conditions – The geometrical and mechanical properties
  4. Stress orientation – critical angles by which stress is applied

    Subdivisions

Strain partitioning across the literature is diverse and has been divided into three subdivisions according to the American Geological Institute.
  1. Superposition of individual strain components that produce the finite strain
  2. The accumulation of strain influenced by constituent rock materials
  3. Individual deformation mechanisms that contribute toward producing the finite strain

    Superposition of individual strain components

The superposition of individual strain components can be expressed at the tectonic scale involving oblique convergent margins and transpression / transtension tectonic regimes.

Oblique convergent margins

Convergent margins where the angle of subduction is oblique will often result in the partitioning of strain into an arc parallel component and an arc normal component. This occurs as a response to shear stress exerted at the base of the overriding plate that is not perpendicular to the plate margin.

Fundamental factors which control strain partitioning within oblique orogens

The Himalaya is a strain partitioned orogen which resulted from the oblique convergence between India and Asia. Convergence between the two landmasses persists today at a rate of 2 cm/yr. The obliquity of plate convergence increases toward the western portion of the orogen, thus inducing a greater magnitude of strain partitioning within the western Himalaya than in the central.
The table below shows relative velocities of India's convergence with Asia. The lateral variability in velocity between the central and marginal regions of the orogen suggest strain is partitioned due to oblique convergence.
LocationArc NormalArc Parallel
Western~10 mm/yr Northward~20 mm/yr Westward
Central~30 mm/yr Northward~0 mm/yr
Eastern~15 mm/yr Northward~20 mm/yr Eastward

Table reference:

Transpression and transtension

Strain partitioning is common within transpressive and transtensive tectonic domains. Both regimes involve a component of pure shear and a component of simple shear. Strain may be partitioned by the development of a strike slip fault or shear zone across the actively deforming region.

Example: Coast Mountains British Columbia

The Coast Mountains of British Columbia are interpreted as a transpressive orogen which formed during the Cretaceous. Oblique subduction induced the development of several shear zones which strike parallel to the orogen. The presence of these shear zones suggest that strain is partitioned within the Coast Orogen which resulted in horizontal translation of terranes for several hundred kilometers parallel to the orogen.

Strain factorization

Strain factorization is a mathematical approach to quantify and characterize the variation of strain components in terms of the intensity and distribution that produces the finite strain throughout a deformed region. This effort is achieved through matrix multiplication. Refer to the figure below to conceptually visualize what is obtained through strain factorization.

Influence of rock material rheology

At the grain and crystal scale, strain partitioning may occur between minerals governed by their rheological contrasts. Constituent minerals of differing rheological properties in a rock will accumulate strain differently, thus inducing mechanically preferable structures and fabrics.

Example

Rocks that contain incompetent minerals such as micas and more competent minerals such as quartz or feldspars, may develop a shear band fabric. The incompetent minerals will preferentially form the C-surfaces and competent minerals will form along the S-surfaces.

Individual deformation mechanisms

Strain partitioning is also known as a procedure for decomposing the overall strain into individual deformation mechanisms which allowed for strain to be accommodated. This approach is performed from geometrical analysis of rocks on the grain – crystal scale. Strain partitioning of deformation mechanisms incorporates those mechanisms which occur both simultaneously and/or subsequently as tectonic conditions evolve, as deformation mechanisms are a function of strain rate and pressure-temperature conditions. Performing such a procedure is important for structural and tectonic analysis as it provides parameters and constraints for constructing deformation models.