Respirator assigned protection factors


The respiratory protective devices can protect workers only if their protective properties are adequate to the conditions in the workplace. Therefore, specialists have developed criteria for the selection of proper, adequate respirators, including the Assigned Protection Factors - the decrease of the concentration of harmful substances in the inhaled air, which to be provided with timely and proper use of a certified respirator of certain types by taught and trained workers, when the employer performs an effective respiratory protective device programme.

Background

The different methods of protection from air pollution and their effectiveness

The imperfection of technological processes, machines and other equipment can lead to air contamination with harmful substances in the workplace. Protecting of the workers' health in this situation may be achieved by different means, listed below in order of decreasing of their effectiveness:
If the use of these methods is impossible, or if their use did not reduce the concentration of harmful substances to a safe value, workers must use respirators. These respirators must be sufficiently effective, and they should correspond to known or expected conditions at the workplace. However, the sole reliance on personal protective equipment for personnel is considered the least effective means of controlling hazards, for reasons including: non-usage of the respirators in the contaminated atmosphere; leakage of unfiltered air through the gaps between the mask and face; and delayed replacement of gas cartridges.

The effectiveness of respirators with different designs

Different terms may be used to describe the protective properties of respirators:
The term "Protection Factor PF" has been used in the U.S., and the term "Penetration" was used in the soviet literature from the 1960s.
In the first half of the 20th century, experts measured protective properties of respirators in the laboratories. They used different control substances. The ratio of the measured concentrations is an indicator of the protective properties of different types of respirators. These measurements showed that if the efficiency of filters is sufficiently high, then the gaps between the mask and the face become the main way of penetration of air contamination under the mask, in the same way that on a cold day, a person wearing a warm jacket and pants will lose most of their heat through the head and extremities.
The shape and size of these gaps is not constant, and depends on many factors. The respirator's PF may change dozens of times during of several minutes; and the two average PF can differ by more than 12 000 times.
Experts believed that the measurement of protection factors in the laboratory allows them to correctly evaluate, predict the RPD efficiency in the workplace conditions. But after the detection of cases of excessive harmful exposure on employees who used high quality respirators with HEPA particle filters in the nuclear industry of the USA, the experts changed their opinion. Studies have been carried out to measure the protection factors for the various types of respirators - not only in the laboratories, but also at the workplaces. Dozens of such field studies have shown that the performance of serviceable respiratory protective equipment at the workplaces may be significantly less than in laboratory conditions. Therefore, the usage of laboratory results to assess the real efficiency is incorrect; and can lead to a wrong choice of such respirators that can not reliably protect workers.

Terminology to describe the different PF, and methods for APF development

The experts used the results of measurements at the laboratories and at the workplaces to develop more completely terminology for description of the respirators' performance; and this terminology has been applied officially, and in the preparation of research results for publication. Specialists began to use different terms to describe the protection factors, which were measured at workplaces with continuous use of respirators; and measured in the workplace when the workers used of respirators intermittently; measured not in the workplace while fit testing; measured in the laboratories under the simulation workplace's conditions; and for the protection factors, that can be expected when the workers properly used the respirators at the workplace.
A significant difference between respirator performance in the laboratories compared to the efficiency at the workplaces not allowed to use the laboratory results to predict the degree of protection offered in practice. And instability of respirators' protective properties prevented evaluate their efficiency. For solving these problems, scientists Donald Campbell and Steven Lenhart suggested to use the results of measurements of Workplace PF values for development of Assigned PF values - as the lower 95% confidence interval of WPF values. The results of measurements of WPF has been used in the development of APF by ANSI. The same was made during the development of the APF by OSHA.

Development of APF values for the various respirator types

Results of measurements of WPF in the US and the UK became the basis for the development of APF for UK standard and for English version of EU standard.
In some cases, there was no information on the effectiveness for respirators of specific design in the workplace. This is due to the fact that the measurement of workplace PF is very difficult, time consuming, and expensive work, which was carried out not very often. For these types of respirators experts used the results of WPF measurements of other types of respirators, which are similar. For example, the effectiveness of the Supplied Air Respirators was considered similar to the efficiency of Powered Air Purifying Respirators, if they have the same facepieces and the same air supply mode. Finally, in the absence of this information, specialists could use the results of Simulated WPF measurements; or estimates of competent experts.

Correction of Assigned PF values

Measurement of workplace protection factors surprisingly revealed the low efficiency of some designs of respirators, and that results have led to a sharp tightening of the requirements for application limits for respirators of such designs.
Measuring WPF of Powered Air Purifying Respirators with helmets showed that the ingress of harmful substances in the inhaled air can be very high. It was a surprise, since earlier studies in the laboratory showed that the flow of clean filtered air from the inside to the outside of the helmet prevents ingress of harmful substances under the helmet. Additional studies have confirmed the result of the first study: the minimum values of the workplace protection factors of 2 models of respirators were 31 and 23; and leakage of unfiltered air achieved 16% in some cases in wind tunnel at 2 m/s air velocity
Therefore, the use of such RPD types was limited 25 PEL in the U.S., and 40 OEL in the UK.
Measurement of protection factors of negative pressure full face masks with high-efficiency filters in the laboratory revealed a risk of decrease in protective properties to a small values. Therefore, the use of such respirators has been limited to the values 50 or 100 PEL in the United States. However, the experts in the UK believed that the quality of their masks is higher than American masks, and were allowed to use up to 900 OEL. But the study showed that the value of the protection factor of > 900 has been achieved in practice infrequently. Minimum protection factors of 3 different models of full facepiece respirators were 11, 18 and 26. So, the new standards limit usage of these respirators up to 40 OEL in UK.
Fit testing of tight-fitting masks of negative-pressure respirators became widely used in US industry in 1980-s. At the beginning, it was thought that the half-mask fit quite well to the worker's face, if during a fit test the protection factor is not less than 10. The widespread use of fit testing in the industry gives professionals optimism, and they allowed to the employers restrict the use of half mask respirators in accordance with the values of worker's personal fit factor, but not more than 100 × PEL. However, scientific studies have shown that although such test increases the effectiveness of protection, the risk of leakage of large amounts of unfiltered air is maintained. Furthermore, the studies have shown that non-filtered air under the mask is not uniformly mixed with the filtered air, which leads to large errors in the measurement of the in-facepiece concentration of contaminants, and subsequent calculations of fit factors - the latter is often much smaller than the "measured" value. So, specialists recommend not allowed usage negative pressure half mask respirators then harmful substances' concentrations exceeds 10 PEL. Therefore, OSHA standards require to restrict using of half-mask negative-pressure respirators up to 10 PEL after obtaining fit factor greater than or equal to 100 during the mask selection for the worker.

Comparison of APF in the US and the UK

The table lists the APF values for the most common respirator types.
US particle filters N95 are similar to P2; and P100 are similar to P3; filtering materials in US N95 filtering facepieces are similar to FFP2. However, in the UK and Europe any tight fitting half mask/full face mask is required to have a second check based on total inward leakage which cannot exceed 8% for FFP2 and 2% for FFP3
The difference of the APF for air purifying negative pressure full-facepiece masks are not large. The difference between PAPR with helmets a few more. But measurements showed that the real effectiveness of RPD is strongly dependent on the conditions of their use, not only from the design, and this partly explains the difference in APF values. The APF for negative pressure half mask respirators are twofold. But this difference cannot be considered separately from recommendations for use of respirators. The use of half-face masks in the US is limited to 10 PEL for the "worst case" - work in the polluted atmosphere of 8 hours per day, 40 hours a week. But British experts took into account large experience of the use of negative pressure air purifying RPDs, and they concluded that to achieve continuous wear respirator 8 hours a day is impossible. For this reason, they recommend to the employer to give the job to the workers so that they work in the polluted atmosphere not during entire shift, but only a part of the shift. The remaining time the employee needs to work in a non-polluted atmosphere. The fact that the employee is in a non-polluted atmosphere some part of working time provide additional protection of his health, and therefore, the requirements to the efficiency of the respirator may be less stringent.
The development of the Assigned PF in the United States and Britain were based on measurements of the effectiveness of respirators in the workplace. Also used opinions of experts, based on the similarity of the respirators with different designs - provided that the mode and the quantity of air supply, and the facepieces were the same. Experts in the two countries often used the results of the same studies of WPF. For example, British standard had been developed with usage of results of 1897 WPF measurements during 31 studies; and 23 of this 31 studies had been conducted in United States.
Therefore, the values of the assigned PF in the US and in the UK are evidence-based; and they are very similar to each other.

The values of the APF in EU and other countries

Studies of respirator's performance was carried out not very often, and almost all of these studies were conducted in USA. It is possible that the lack of information about the RPD efficiency in the workplaces, was the reason behind developing these assigned PF in several European countries, whose values differ significantly from the evidence-based values of APFs in the US and UK.
Most European countries did not conduct very complex and expensive studies on the effectiveness of respirators in the workplaces, or spent very little of such research. Therefore, it may be that some countries do not take full account of results of foreign researches. For example, after the study in 1990, the APF value of negative pressure full face masks was reduced from 900 to 40 in UK. But in other countries, similar research was not carried out; and a similar decrease did not occur.
The study showed that the three models of full face masks had a significant leakage of unfiltered air through the gaps between the mask and the face. The minimum values of the workplace protection factors of each of the three negative pressure full face mask models were 11, 17 and 26. The maximum value of the WPF from one of the models did not exceed 500 no times at all. And for all results together, the WPF was not more than 100 in ~ 30% of the measurements. So, for this reason, the values of the APFs for this RPD type in Germany, Finland, Italy, and Sweden, may not fully take into account the lower this type respirators' performance at the workplace compared to the performance in the laboratory. The same was true for other RPD types and their APF.
State standard in India points to the need to use the workplace protection factors for restricting the permissible use of respirators, but does not set any values of the APFs. The standard also recommends the use of those PFs, which are obtained during the certification. These values greatly exceed the values used in the USA and in the UK.
The Ukrainian version of the EU standard EN 529 does not set any values of the APFs for the selection of respirator in this country. This document only listed the values of APFs in several European countries ; and declares the inadmissibility of the use of laboratory efficiency for predicting the protective properties at the workplace.
The APFs are not developed in RF, in South Korea, as well as in many other countries, and selection of respirators is not regulated by its national legislation. This contributes to errors, and the usage of such respirator's types, which are not able to reliably protect the workers due to its design.

The use of the APFs when selecting respirators for known workplace conditions

US law obliges the employer to accurately measure air pollution at workplaces. The results of such measurements are used to assess whether short-term inhalation of harmful substances may lead to irreversible and significant deterioration of health, or death. If concentrations exceed the IDLH, the standard allows the use of only the most reliable respirators - SAR or self-contained breathing apparatus: with pressure-demand air supply in the full facepiece mask ).
If the concentration of a harmful substance is less than the IDLH, the coefficient of air pollution for the harmful substance is determined, which is equal to the ratio of this concentration to the PEL for the harmful substance. The APF of the selected respirator type must equal or exceed the Hazard Factor.
If there are several harmful substances in the workplace air, then the selected respirator must meet the following requirement:
C1/ + C2/ + C3/ +... + Cn/ ≤ 1
where C1, C2... and Cn are the concentrations of harmful substances number 1, 2... n; and PEL is the maximum allowable concentration for corresponding harmful substances in the breathing zone.
If this requirement is not met, the employer needs to choose a different type of respirator, which has a greater APF value.
In all cases, if they employer selects a respirator with tight-fitting facepiece, all employee must be fit tested. Appendix A provides a detailed description of this testing.
Values of IDLH concentrations and detailed recommendations for the selection of respirators are available in the NIOSH directory.

International standard for RPD selection and usage

is developing two international standards that govern the certification of respirators; and their selection and application
The standards governing the selection of respirators use the APF value. But HSE specialists critique these documents, noting these standards are set to values of APF that differ from those established in the US and the UK; and these values are set not for a specific RPD type but rather for any RPD that meets approval requirements:
The report concluded that new ISO standards set insufficiently high APF values and recommended that these values should not be used in practice, and to continue work on APF justification for the different types of respirators.