The Pattern 1907 bayonet, officially called the Sword bayonet, pattern 1907 , was a British bayonet designed to be used with the Short Magazine Lee Enfield rifle. The Pattern 1907 bayonet was used by the British and Commonwealth forces throughout both the First and Second World Wars.
Design
The Pattern 1907 bayonet consisted of a one-piece steel blade and tang, with a crossguard and pommel made from wrought iron or mild steel, and a wooden grip usually of walnut secured to the tang by two screws. The entire bayonet was long and weighed, although the weight of production models varied from. Originally the bayonet featured a hooked lower quillion, intended to be used to trap and snap enemy bayonets when grappling, this was later deemed impractical and replaced with a simpler design from 1913, often unit armourers subsequently removed the hooked quillion when the bayonet went for repair, although there is no evidence that this was officially directed. The Pattern 1907 bayonet's blade was long, it had a shallow fuller that was machined into both sides of the blade to save weight and add strength, the fuller was long that extended to within of the tip. The Pattern 1907 bayonet was supplied with a simple leather scabbard flitted with a steel top-mount and chape, it was usually carried from the belt by a simple frog. The Pattern 1907 bayonet attached to the SMLE by a boss located below the barrel on the nose of the rifle and a mortise groove on the pommel of the bayonet. The combined length of the SMLE and Pattern 1907 bayonet was.
Markings
Official marks were stamped onto the Pattern 1907 bayonet's ricasso. On British manufactured bayonets the right side included an 'X' bend-test mark, a broad arrow government acceptance mark, and one or more Royal Small Arms Factory appointed inspector's marks, on the left side was the date of the bayonet's official inspection and the maker's name and the reigning monarch's crown and royal cypher, 'ER' and after 1910 'GR'. Indian bayonets were marked similarly to British bayonets except the royal cypher read 'GRI' and the manufacturer's mark was 'R.F.I.'. Australian bayonets differed in the manufacturer's marks, with 'Lithgow', 'MA' and 'OA'. The wooden grips of World War II era Australian bayonets were often marked 'SLAZ' for Slazenger, who made the grips during that war.
History
When the British military adopted the Short Magazine Lee-Enfield rifle and its barrel was shortened to, shorter than the preceding Magazine Lee-Enfield. British military strategists were fearful that the British infanteer would be at a disadvantage when engaged in a bayonet duel with enemy soldiers who retained a longer reach, bayonet fighting drills formed a significant part of a contemporary British infanteer's training, soldiers were drilled in various stances and parrying techniques against an enemy also armed with rifle and bayonet. The combined length of the SMLE and the in-service Pattern 1903 bayonet and its 12-inch blade was, shorter than the contemporary French Lebel Model 1886 and bayonet at and the German Mauser 1898 at and bayonet. In 1906–7 the British Army conducted trials to find a new longer standard issue bayonet, experiments were conducted with a number of foreign bayonet designs, including a modified version of the American Model 1905 bayonet and the Japanese Type 30 bayonet. The trials resulted in the British Army adopting its own version of the Type 30 bayonet, the new design was designated Sword bayonet, pattern 1907 and was officially introduced on 30 January 1908. Approximately 5,000,000 Pattern 1907 bayonets were made in Britain during World War I, the makers were Wilkinson Sword, Sanderson Brothers & Newbould Ltd, James A. Chapman, Robert Mole & Sons and Vickers Ltd, additionally Remington UMC produced approximately 100,000 during the war. The Pattern 1907 bayonet was manufactured in India from 1911 to 1940 at the Rifle Factory Ishapore and in Australia from 1913 to 1927 then again between 1940 and 1945 at the Lithgow Small Arms Factory, Mangrovite Arsenal and Orange Arsenal. The Pattern 1907 bayonet was adopted by most of the British Commonwealth along with the SMLE, it saw broad front line service until 1945, seeing service in both World War I and World War II, it remained in Australian and Indian service for some time after 1945. In 1926 the 1907 bayonet was reclassified as the 'Bayonet, No.1, Mk.1'
Variants
Pattern 1913 bayonet
The Pattern 1913 bayonet was designed to be used with the experimental Pattern 1913 Enfield. The Pattern 1913 bayonet's only functional difference from the Pattern 1907 bayonet was the cross guard for the muzzle ring is longer, to fit the Pattern 1913 Enfield rifle. Upon the outbreak of World War I the British authorities adapted the Pattern 1913 Enfield to the.303 British cartridge, creating the Pattern 1914 Enfield rifle, and contracts were awarded to the United States arms manufacturers Winchester, Remington and Eddystone for the rifle's production. To accompany those rifles, Remington manufactured the 1,243,000 Pattern 1913 bayonets and Winchester produced 225,000. The Pattern 1917 bayonet cannot be fixed to the Lee-Enfield rifle, so to avoid confusion with the Pattern 1907 bayonet, two deep vertical grooves were cut into the wooden grips of the Pattern 1913 bayonet.
Model 1917 bayonet
Upon their entry into World War I, the United States military adapted the Pattern 1914 Enfield rifle to the.30-06 Springfield cartridge to make up for shortfalls in production of the Model 1903 Springfield rifles, creating the substitute standard Model 1917 Enfield rifle. To accompany the M1917 rifle, the United States simply adopted the Pattern 1913 bayonet as the Model 1917 bayonet. Over 2,000,000 Model 1917 bayonets were manufactured in the United States during the war, including 545,000 Pattern 1913 bayonets manufactured for but not delivered to the British military, that were simply re-stamped as Model 1917 bayonets. The Model 1917 bayonet was adopted unchanged to be used with United States Armycombat shotguns, after the war, the M1917 bayonet was retained for use with combat shotguns, it remained in United States service until the 1980s.
India Pattern bayonets
From 1941, India began cutting down Pattern 1907 bayonets to and grinding a point into the remaining blade, creating the India Pattern No. 1 Mk. I*, the India Pattern No. 1 Mk. I** is almost identical except a false blade long is ground into the top of the blade, both were recognisable as the fuller than now ran the length of the blade. The India Pattern No. 1 Mk. II and the India Pattern No. 1 Mk. II* were newly manufactured versions with 12.2 inch blades that had no fuller, the latter having a false blade on top side, both retained the Pattern 1907 hilt and grip. The India Pattern No. 1 Mk. III and the India Pattern No. 1 Mk. III* were similar to the No. 1 Mk. II and No. 1 Mk. II* except they had crude squared pommels, rectangular grips and were finished with black paint.
