Microfiltration


Microfiltration is a type of filtration physical process where a contaminated fluid is passed through a special pore-sized membrane to separate microorganisms and suspended particles from process liquid. It is commonly used in conjunction with various other separation processes such as ultrafiltration and reverse osmosis to provide a product stream which is free of undesired contaminants.

General principles

Microfiltration usually serves as a pre-treatment for other separation processes such as ultrafiltration, and a post-treatment for granular media filtration. The typical particle size used for microfiltration ranges from about 0.1 to 10 μm. In terms of approximate molecular weight these membranes can separate macromolecules of molecular weights generally less than 100,000 g/mol. The filters used in the microfiltration process are specially designed to prevent particles such as, sediment, algae, protozoa or large bacteria from passing through a specially designed filter. More microscopic, atomic or ionic materials such as water, monovalent species such as Sodium or Chloride ions, dissolved or natural organic matter, and small colloids and viruses will still be able to pass through the filter.
The suspended liquid is passed through at a relatively high velocity of around 1–3 m/s and at low to moderate pressures parallel or tangential to the semi-permeable membrane in a sheet or tubular form. A pump is commonly fitted onto the processing equipment to allow the liquid to pass through the membrane filter. There are also two pump configurations, either pressure driven or vacuum. A differential or regular pressure gauge is commonly attached to measure the pressure drop between the outlet and inlet streams. See Figure 1 for a general setup.
The most abundant use of microfiltration membranes are in the water, beverage and bio-processing industries. The exit process stream after treatment using a micro-filter has a recovery rate which generally ranges to about 90-98 %.

Range of applications

Water treatment

Perhaps the most prominent use of microfiltration membranes pertains to the treatment of potable water supplies. The membranes are a key step in the primary disinfection of the uptake water stream. Such a stream might contain pathogens such as the protozoa Cryptosporidium and Giardia lamblia which are responsible for numerous disease outbreaks. Both species show a gradual resistance to traditional disinfectants. The use of MF membranes presents a physical means of separation as opposed to a chemical alternative. In that sense, both filtration and disinfection take place in a single step, negating the extra cost of chemical dosage and the corresponding equipment.
Similarly, the MF membranes are used in secondary wastewater effluents to remove turbidity but also to provide treatment for disinfection. At this stage, coagulants may potentially be added to precipitate species such as phosphorus and arsenic which would otherwise have been soluble.

Sterilization

Another crucial application of MF membranes lies in the cold sterilisation of beverages and pharmaceuticals. Historically, heat was used to sterilize refreshments such as juice, wine and beer in particular, however a palatable loss in flavour was clearly evident upon heating. Similarly, pharmaceuticals have been shown to lose their effectiveness upon heat addition. MF membranes are employed in these industries as a method to remove bacteria and other undesired suspensions from liquids, a procedure termed as 'cold sterilisation', which negate the use of heat.

Petroleum refining

Furthermore, microfiltration membranes are finding increasing use in areas such as petroleum refining, in which the removal of particulates from flue gases is of particular concern. The key challenges/requirements for this technology are the ability of the membrane modules to withstand high temperatures, but also the design must be such to provide a very thin sheeting to facilitate an increase of flux. In addition the modules must have a low fouling profile and most importantly, be available at a low-cost for the system to be financially viable.

Dairy processing

Aside from the above applications, MF membranes have found dynamic use in major areas within the dairy industry, particularly for milk and whey processing. The MF membranes aid in the removal of bacteria and the associated spores from milk, by rejecting the harmful species from passing through. This is also a precursor for pasteurisation, allowing for an extended shelf-life of the product. However, the most promising technique for MF membranes in this field pertains to the separation of casein from whey proteins. This results in two product streams both of which are highly relied on by consumers; a casein-rich concentrate stream used for cheese making, and a whey/serum protein stream which is further processed to make whey protein concentrate. The whey protein stream undergoes further filtration to remove fat in order to achieve higher protein content in the final WPC and WPI powders.

Other applications

Other common applications utilising microfiltration as a major separation process include
Membrane filtration processes can be distinguished by three major characteristics: driving force, retentate stream and permeate streams. The microfiltration process is pressure driven with suspended particles and water as retentate and dissolved solutes plus water as permeate. The use of hydraulic pressure accelerates the separation process by increasing the flow rate of the liquid stream but does not affect the chemical composition of the species in the retentate and product streams.
A major characteristic that limits the performance of microfiltration or any membrane technology is a process known as fouling. Fouling describes the deposition and accumulation of feed components such as suspended particles, impermeable dissolved solutes or even permeable solutes, on the membrane surface and or within the pores of the membrane. Fouling of the membrane during the filtration processes decreases the flux and thus overall efficiency of the operation. This is indicated when the pressure drop increases to a certain point. It occurs even when operating parameters are constant Fouling is mostly irreversible although a portion of the fouling layer can be reversed by cleaning for short periods of time.

Microfiltration membranes can generally operate in one of two configurations.

Dead-end filtration; all of the process fluid flows and all particles larger than the pore sizes of the membrane are stopped at its surface. All of the feed water is treated at once subject to cake formation. This process is mostly used for batch or semicontinuous filtration of low concentrated solutions, Refer to Figure 3 for a general schematic for this process.

Process and equipment design

The major issues that influence the selection of the membrane include

Site-specific issues

A few important design heuristics and their assessment are discussed below:
Like any other membranes, microfiltration membranes are prone to fouling. It is therefore necessary that regular maintenance be carried out to prolong the life of the membrane module.
The cost to design and manufacture a membrane per unit of area are about 20% less compared to the early 1990s and in a general sense are constantly declining. Microfiltration membranes are more advantageous in comparison to conventional systems. Microfiltration systems do not require expensive extraneous equipment such as flocculates, addition of chemicals, flash mixers, settling and filter basins. However the cost of replacement of capital equipment costs might still be relatively high as the equipment may be manufactured specific to the application. Using the design heuristics and general plant design principles, the membrane life-span can be increased to reduce these costs.
Through the design of more intelligent process control systems and efficient plant designs some general tips to reduce operating costs are listed below
Table 1 expresses an indicative guide of membrane filtration capital and operating costs per unit of flow.
ParameterAmountAmountAmountAmountAmount
Design Flow 0.010.11.010100
Average Flow 0.0050.030.354.450
Capital Cost $18.00$4.30$1.60$1.10$0.85
Annual Operating and Managing Costs $4.25$1.10$0.60$0.30$0.25

Table 1 Approximate Costing of Membrane Filtration per unit of flow
Note:

Membrane materials

The materials which constitute the membranes used in microfiltration systems may be either organic or inorganic depending upon the contaminants that are desired to be removed, or the type of application.
General Membrane structures for microfiltration include
Plate and frame
Membrane modules for dead-end flow microfiltration are mainly plate-and-frame configurations. They possess a flat and thin-film composite sheet where the plate is asymmetric. A thin selective skin is supported on a thicker layer that has larger pores. These systems are compact and possess a sturdy design, Compared to cross-flow filtration, plate and frame configurations possess a reduced capital expenditure; however the operating costs will be higher. The uses of plate and frame modules are most applicable for smaller and simpler scale applications which filter dilute solutions.
Spiral-wound
This particular design is used for cross-flow filtration. The design involves a pleated membrane which is folded around a perforated permeate core, akin to a spiral, that is usually placed within a pressure vessel. This particular design is preferred when the solutions handled is heavily concentrated and in conditions of high temperatures and extreme pH. This particular configuration is generally used in more large scale industrial applications of microfiltration.

Fundamental design equations

As separation is achieved by sieving, the principal mechanism of transfer for microfiltration through micro porous membranes is bulk flow.
Generally, due to the small diameter of the pores the flow within the process is laminar The flow velocity of the fluid moving through the pores can thus be determined, the simplest of which assuming a parabolic velocity profile.
Transmembrane Pressure
The transmembrane pressure is defined as the mean of the applied pressure from the feed to the concentrate side of the membrane subtracted by the pressure of the permeate. This is applied to dead-end filtration mainly and is indicative of whether a system is fouled sufficiently to warrant replacement.
Where
Permeate Flux
The permeate flux in microfiltration is given by the following relation, based on Darcy's Law
Where
The cake resistance is given by:
Where
For micron sized particles the Specific Cake Resistance is roughly.
Where
Rigorous design equations
To give a better indication regarding the exact determination of the extent of the cake formation, one-dimensional quantitative models have been formulated to determine factors such as
See External Links for further details

Environmental issues, safety and regulation

Although environmental impacts of membrane filtration processes differ according to the application, a generic method of evaluation is the life-cycle assessment, a tool for the analysis of the environmental burden of membrane filtration processes at all stages and accounts for all types of impacts upon the environment including emission to land, water and air.
In regards to microfiltration processes, there are a number of potential environmental impacts to be considered. They include global warming potential, photo-oxidant formation potential, eutrophication potential, human toxicity potential, freshwater ecotoxicity potential, marine ecotoxicity potential and terrestrial ecotoxicity potential. In general, the potential environmental impact of the process is largely dependent on flux and the maximum transmembrane pressure, however other operating parameters remain a factor to be considered. A specific comment on which exact combination of operational condition will yield the lowest burden on the environment cannot be made as each application will require different optimisations.
In a general sense, membrane filtration processes are relative "low risk" operations, that is, the potential for dangerous hazards are small. There are, however several aspects to be mindful of. All pressure-driven filtration processes including microfiltration requires a degree of pressure to be applied to the feed liquid stream as well as imposed electrical concerns. Other factors contributing to safety are dependent on parameters of the process. For example, processing dairy product will lead to bacteria formations that must be controlled to comply with safety and regulatory standards.

Comparison with similar processes

Membrane microfiltration is fundamentally the same as other filtration techniques utilising a pore size distribution to physically separate particles. It is analogous to other technologies such as ultra/nanofiltration and reverse osmosis, however, the only difference exists in the size of the particles retained, and also the osmotic pressure. The main of which are described in general below:

Ultrafiltration

Ultrafiltration membranes have pore sizes ranging from 0.1 μm to 0.01 μm and are able to retain proteins, endotoxins, viruses and silica. UF has diverse applications which span from waste water treatment to pharmaceutical applications.

Nanofiltration

Nanofiltration membranes have pores sized from 0.001 μm to 0.01 μm and filters multivalent ions, synthetic dyes, sugars and specific salts. As the pore size drops from MF to NF, the osmotic pressure requirement increases.

Reverse osmosis

Reverse Osmosis is the finest separation membrane process available, pore sizes range from 0.0001 μm to 0.001 μm. RO is able to retain mostly all molecules except for water and due to the size of the pores, the required osmotic pressure is significantly greater than that for MF. Both reverse osmosis and nanofiltration are fundamentally different since the flow goes against the concentration gradient, because those systems use pressure as a means of forcing water to go from low pressure to high pressure.

Recent developments

Recent advances in MF have focused on manufacturing processes for the construction of membranes and additives to promote coagulation and therefore reduce the fouling of the membrane. Since MF, UF, NF and RO are closely related, these advances are applicable to multiple processes and not MF alone.
Recently studies have shown dilute KMnO4 preoxidation combined FeCl3 is able to promote coagulation, leading to decreased fouling, in specific the KMnO4 preoxidation exhibited an effect which decreased irreversible membrane fouling.
Similar research has been done into the construction high flux poly nanofiber membranes, focusing on increased throughput. Specialised heat treatment and manufacturing processes of the membrane's internal structure exhibited results indicating a 99.6% rejection rate of TiO2 particles under high flux. The results indicate that this technology may be applied to existing applications to increase their efficiency via high flux membranes.