Mdadm


mdadm is a Linux utility used to manage and monitor software RAID devices. It is used in modern GNU/Linux distributions in place of older software RAID utilities such as raidtools2 or raidtools.
mdadm is free software maintained by, and copyrighted to, Neil Brown of SUSE, and licensed under the terms of version 2 or later of the GNU General Public License.

Name

The name is derived from the md device nodes it administers or manages, and it replaced a previous utility mdctl. The original name was "Mirror Disk", but was changed as more functions were added. The name is now understood to be short for Multiple Disk and Device Management.

Overview

Linux software RAID configurations can include anything presented to the Linux kernel as a block device. This includes whole hard drives, and their partitions.

RAID configurations

RAID 10 is distinct from RAID 0+1, which consists of a top-level RAID 1 mirror composed of high-performance RAID 0 stripes directly across the physical hard disks. A single-drive failure in a RAID 10 configuration results in one of the lower-level mirrors entering degraded mode, but the top-level stripe performing normally. A single-drive failure in a RAID 0+1 configuration results in one of the lower-level stripes completely failing, and the top-level mirror entering degraded mode. Which of the two setups is preferable depends on the details of the application in question, such as whether or not spare disks are available, and how they should be spun up.

Non-RAID configurations

The original form of names for md devices is, where is a number between 0 and 99. More recent kernels have support for names such as. Under 2.4.x kernels and earlier these two were the only options. Both of them are non-partitionable.
Since 2.6.x kernels, a new type of MD device was introduced, a partitionable array. The device names were modified by changing to. The partitions were identified by adding, where is the partition number; thus for example. Since version 2.6.28 of the Linux kernel mainline, non-partitionable arrays can be partitioned, the partitions being referred to in the same way as for partitionable arrays for example,.
Since version 3.7 of the Linux kernel mainline, md supports TRIM operations for the underlying solid-state drives, for linear, RAID 0, RAID 1, RAID 5 and RAID 10 layouts.

Booting

Since support for MD is found in the kernel, there is an issue with using it before the kernel is running. Specifically it will not be present if the boot loader is either LiLo or GRUB legacy. Although normally present, it may not be present for GRUB 2. In order to circumvent this problem a filesystem must be used either without md support, or else with RAID1. In the latter case the system will boot by treating the RAID1 device as a normal filesystem, and once the system is running it can be remounted as md and the second disk added to it. This will result in a catch-up, but filesystems are usually small.
With more recent bootloaders it is possible to load the MD support as a kernel module through the initramfs mechanism. This approach allows the filesystem to be inside any RAID system without the need of a complex manual configuration.

External metadata

Besides its own formats for RAID volumes metadata, Linux software RAID also supports external metadata formats, since version 2.6.27 of the Linux kernel and version 3.0 of the userspace utility. This allows Linux to use various firmware- or driver-based RAID volumes, also known as "fake RAID".
, there are two supported formats of the external metadata:
mdmpd was a daemon used for monitoring MD multipath devices up to Linux kernel 2.6.10-rc1, developed by Red Hat as part of the mdadm package. The program was used to monitor devices, and is usually started at boot time as a service, and afterwards running as a daemon.
Enterprise storage requirements often include the desire to have more than one way to talk to a single disk drive so that in the event of some failure to talk to a disk drive via one controller, the system can automatically switch to another controller and keep going. This is called multipath disk access. The linux kernel implements multipath disk access via the software RAID stack known as the md driver. The kernel portion of the md multipath driver only handles routing I/O requests to the proper device and handling failures on the active path. It does not try to find out if a path that has previously failed might be working again. That's what this daemon does. Upon startup, it reads the current state of the md raid arrays, saves that state, and then waits for the kernel to tell it something interesting has happened. It then wakes up, checks to see if any paths on a multipath device have failed, and if they have then it starts to poll the failed path once every 15 seconds until it starts working again. Once it starts working again, the daemon will then add the path back into the multipath md device it was originally part of as a new spare path.
If one is using the filesystem, lists all active md devices with information about them. Mdmpd requires this to find arrays to monitor paths on, to get notification of interesting events and to monitor array reconstruction on Monitor mode.