M809 series 5-ton 6x6 truck
The M809 Series 5-ton 6x6 truck was a family of heavy tactical trucks built for the United States Armed Forces. The basic cargo version was designed to transport a 5-ton, long load over all terrain in all weather. In on-road service the load weight was doubled. Built by AM General, they evolved into the M939 Series.
History
In the late 1960s the US Army needed more 5-ton 6x6 trucks. Kaiser-Jeep developed an updated version of the M39 series which had been in service since 1951. The primary difference was the engine change to Cummins. The hood and grille were lengthened to make room for the longer engine and the lighting system was updated to meet new US safety regulations. All had an air cleaner on the left fender, a way to tell them from the earlier M39 series.Kaiser-Jeep was awarded the M809-series contract DAAE06-69-C-0009 and built them during 1969 and into 1970. In February 1970, Kaiser-Jeep was purchased by American Motors Corporation and on March 26, 1970, Kaiser-Jeep was reorganized as the "Jeep Corporation." The South Bend facilities where the M809-series was being built subsequently became Jeep Corporation's "General Products Division." Just over a year later, on March 31, 1971, this General Products Division was spun off and became "AM-General," a wholly owned subsidiary of American Motors Corporation. In 1974, a new contract for the M809-series was awarded to AM General, DAAE07-74-C-0120. This contract covered trucks built over the next 5 years at least. AM-General built all M809-series trucks between 1971 and 1982. In 1982, the M809-series was then improved into the M939 series. The first 11,000 M939s were rebuilds of M809s.
Specifications
Engine and driveline
The M809 series used a Cummins NHC250 engine, a Engine displacement| naturally aspirated inline 6 cylinder diesel engine developing Horsepower| at 2100rpm and of torque at 1500rpm. All models of the M809 series used this engine throughout their service life. The N series was a successful commercial design, with a conservative rating the engine was more powerful and less stressed than the Continental LDS-465 multifuel engine used in the M39 series.A Dana-Spicer 5-speed model 6453 synchromesh manual transmission had a very low 1st, direct 4th, and overdrive 5th. A Rockwell-Standard 2-speed transfer case also engaged the front axle automatically if the rear wheels turned faster than the front, as when the rear wheels spun, in any gear and any range.
Chassis
The M809 series had a ladder frame with three live axles, the front on leaf springs and the rear tandem on leaf springs with locating arms.There were three wheelbases. The short, used for tractors and dumps, was, the long, used for cargo, wreckers, and bolsters, was, and the extra long, used for long cargo, tractor wreckers, and expansible vans, was.
Most models had 11.00x20 size tires with dual rear tires. Some M813s had 14.00x20 with single rear tires, the M821 bridge trucks had 14.00x20 with dual rear tires. The M819 wrecker tractor had 12.00x20 with dual rear tires. All tires were bi-directional military pattern.
Brakes were air over hydraulic with drum brakes on all wheels. Air brake connections at the rear were used for trailer brakes. The M815, M818, and M819 had separate controls to apply the trailer brakes separately from the service brakes.
All M809 models had a rear pintle hitch and could tow trailers except the M816, which could tow The M818 and M819 could tow semi trailers on their fifth wheel.
Many M809 series were equipped with a front-mounted capacity winch, intended for self-recovery. A winch weighed and added inches to the length of the truck. The M815 had a mid-mounted winch and the M816 had a rear-mounted capacity winch.
A standard military cab, designed by REO for their -ton M35, was used. It had hinged doors with roll-up windows, a folding windshield, and a removable canvas roof. A hard roof could be fitted.
Models
M813 & M814 Cargo trucks
The M813 was the standard cargo version of the series. It had a long low sided box with a bottom hinged tailgate. Side racks, troop seats, and overhead bows with a tarpaulin were standard. A front-mounted winch was optional.The standard body sides could secure a load but could not be loaded from the side by forklifts, so a body with drop sides was standardized as the M813A1.
The M814, with an extra long wheelbase, had a long box. There was no drop side version of the M814, and none had troop seats.
M815 Bolster logging truck
The M815 Bolster logging truck, with the M796 bolster trailer, was used to carry long loads like logs, poles, pipes, and bridge sections. The front of the load was secured to a rotating bolster on the truck and the rear of the load was secured to the trailer. The truck and trailer had a tubular boom that connected them under the load. When the truck was unloaded the trailer could be loaded onto the truck. The truck had a large cab protection rack and both front and mid mounted winches.M816 Medium wrecker truck
The M816 Medium wrecker truck was used to recover disabled or stuck trucks and lift large components. A rotating, telescoping, and elevating hydraulic boom could lift a maximum of. Although the truck was not meant to carry a load, the boom could support when towing. They had front and rear winches, outriggers, boom braces, chocks, block and tackle, oxygen-acetylene torches, and other automotive tools.M817 Dump truck
The M817 dump truck was used to haul sand, gravel, dirt, rubble, scrap, and other bulk materials. It had a dump body with cab protector and a tailgate that could hinge at either the top or bottom. Normal loads are heavy by volume, the dump body was smaller and more heavily built than a cargo body. They could be equipped with overhead bows, tarpaulin, and troop seats, but the relatively small size of the body limited their passenger or cargo load.M818 Tractor unit|Tractor trucks
M818 Tractor trucks were used to tow semi-trailers up to with on their fifth wheel. Semi-tractor/trailers have to stay on relatively flat ground, and are not rated for full off-road use. On improved roads they could tow up to with on their fifth wheel.The M818 normally towed a 12-ton 2 axle trailer. There were stake and platform, van, low-bed, and tanker bodies. 6-ton 2 axle expansible vans and 6-ton single axle vans were also used.
M819 Medium wrecker tractor truck
The M819 Medium wrecker tractor truck, with an extra long wheelbase, was a wrecker with a fifth wheel mounted behind the boom. This let the truck load and tow semi trailers. Meant for aircraft recovery, they had a smaller body and less equipment than the M816.All had a front winch, the fifth wheel replaced the rear winch. As a wrecker the boom could lift up to, and had a longer reach than the M816. As a tractor the fifth wheel load rating was. Because of the high empty weight as a semi tractor, oversize 12.00x20 tires were used, this was the only model to have this size.