IDEDOS


IDEDOS is a ROM-based disk operating system written in 6502/65816 assembly language for the Commodore 64, 128 and SuperCPU. Its main purpose is to control ATA devices connected to an IDE64 cartridge and present them like normal Commodore drives. Additionally it supports networked drives and has a built-in machine code monitor and file manager.

Architecture

The C64 KERNAL uses a vector table at page 3 to allow redirection of common kernal file handling and basic functions. This feature is used by IDEDOS to hook into the C64 kernal.
The operating system itself is divided into four pages of 16 KiB which are mapped in when required. The mapping is temporarily switched off while interrupts are running for increased compatibility, however this causes a ≈40 μs latency.
Additional RAM for buffers and internal data are also mapped in from either the IDE64 cartridge or the additional RAM of the SuperCPU is used. The standard kernal memory locations at page zero and page two are handled in a kernal-compatible way; temporarily used memory is restored after the routines are finished.
Beyond the kernal table IDEDOS has two new calls for bulk data handling which allows much faster data transfer rates than the character-based I/O.
The native file system is non-CBM style at the low level to allow partitions greater than 16 MiB. High-level features like the 16-character filenames or filetypes are retained. Due to complexity and memory requirements, the filesystem creation and consistency check is not part of the operating system, unlike CBM DOS or CMD DOS.
Additional filesystems like ISO 9660 or FAT are abstracted internally and mostly use the same routines for handling, thereby little difference is noticeable to user programs, except if some features are not fully implemented.
The device handling is done by additional device numbers assigned to the new devices. The device numbers for IDEDOS devices are configurable and is normally in the range of 10–14. Over the years many programs assumed that there is only device 8 and do not allow selecting anything else; this can be worked around by temporary changing the used IDEDOS device number to 8.
For standard devices, the original kernal routines are used, while IDEDOS devices use custom routines which closely imitate the results and behavior of kernal calls for floppy devices. Kernal calls not going through the vector table present an incompatibility with those programs using them.
Special features are implemented by new channel 15 commands, while features not found on floppy drives follow the CMD style commands to allow programs to easily support a wider range of devices.
Unlike intelligent external devices which have a separate processor, IDEDOS runs on the host computer, thereby all disk routines block until finished. This rules out the use of "IRQ loaders" which are commonly used to speed up operation of serial bus peripherals.
Interrupts are generally allowed while IDEDOS is running, however the system was written to be non-reentrant, just like the original kernal.

Short history

In 1996 IDEDOS was born, as there was a need for a system to run the IDE64 1.1 card. It was created by Josef Souček and Tomáš Přibyl. Additional code came by Jan Vorlíček, Jan Hlaváček.
In 2000 Kajtár Zsolt added CDROM support, new setup code and lot of fixes. Due to limitations of the design the development of a completely rewritten version was started by Kajtár Zsolt, which was not ready for general use before 2005. Meanwhile, the old version reached 0.898b in June 2004.
In 2009 the 64 KiB limit for the system started to get tight, and the IDEDOS 0.91 beta was started to refactor the code to gain more space and internal flexibility.

IDEDOS 0.898b

This was the last version of the old IDEDOS series.

Device support

Built in fast loader supported devices:
Fast load can be switched off in setup in case of incompatibility. Minimum interleave is 7, fast saver is only supported in manager, and uses an interleave of 8. PAL/NTSC compatible timing.

PCLink

Custom protocol, sequential access only. Supported devices:
Includes clock with calendar, ability to set drive numbers, screen colours, auto boot, floppy fast loader, basic clock, power management, write retry, read-ahead and write cache drive settings, CDROM slow down option.

BASIC extensions

The BASIC extension includes disk handling commands, and adds some new error messages. Commands:
It can be used to navigate around directories, start programs, copy/rename/delete files, create directories, and execute plugins to operate on files. Recursive file copy was only added in 0.898b, and in rare cases it does not work.

Monitor

The monitor is almost exactly the Final cartridge monitor in IDEDOS 0.89. Only standard 6502 opcodes are available. The commands are:
This is the current stable, the latest version is 20100509. Most notable differences to 0.89 are:
Supported devices:
Device support is automatically detected, but can be disabled manually if needed. PAL/NTSC compatible timing. Fast saver only in the file manager.

PCLink

Custom protocol, sequential access only. Supported devices:
Mostly the well known standard DOS wedge commands.
The BASIC extension adds disk handling commands, which can be used with any device because they use CMD style commands.
The file managers inspiration comes from 0.89, though it was rewritten from scratch. The goal was to have a file manager which not only supports IDEDOS devices, but also works well with CMD and other drives.

Monitor

The monitor was rewritten from scratch, the main inspiration was the CCS64 emulator's monitor, but some command ideas came from FC3/AR7/Vice monitors. The goal was to have freezer style and fast machine code monitor which supports illegal 6502 and SuperCPU emulation mode opcodes.
Commands:
This is still in development. Most notable differences to 0.90 are: