HVDC Volgograd–Donbass


The HVDC Volgograd–Donbass is a long bipolar ±400 kV high voltage direct current powerline used for transmitting electric power from Volga Hydroelectric Station at Volgograd in Russia to Donbass in eastern Ukraine and vice versa.
The Volgograd–Donbass system was the second HVDC scheme built in the former Soviet Union, following the Moscow-Kashira HVDC scheme which had already been shut down. The Volgograd–Donbass system can transfer a maximum power of 750 MW. When completed in 1965, its operating voltage of ±400 kV was the highest in the world, and remained so until the completion of the ±450 kV Nelson River scheme in 1977. The scheme is today in a bad state and only operated with a voltage of 100 kV. Nevertheless, it is still being modernized, as a Google Map Picture of its crossing with M-4 motorway at shows, where one can see that new pylons for the crossing of the motorway are under construction.
There are concerns of mercury contamination of the area near the Ukrainian terminal, if it got destroyed at the Ukrainian Civil War .
Some towers of the line north of Smile at 48°43'21"N 38°52'20"E were destroyed in the Ukrainian War.

Volzhskaya converter station

The terminal at Volga Hydroelectric Station, Volzhskaya converter station, is situated on the dam of the power plant at. Each of the poles consist of four series connected three-phase valve bridges, which form two series connected twelve pulse bridges. Originally all valves of the scheme were mercury arc valves designed for a voltage of 100 kV and a maximum current of 938 Amperes. Unusually for valves of such high current rating, each valve used only a single anode but because the peak reverse voltage rating was quite limited, two valves were connected in series in each converter arm. The valves used oil-cooled cathode tanks and natural air-cooled anode insulators, with internal grading electrodes inside the porcelain. Each valve stood 3.5 m tall and weighed about 2 tonnes.
In 1977 one mercury arc valve group was replaced by a thyristor valve group. The converter transformers of Volzhskaya converter station are fed directly from the generators of the Volga Hydroelectric Station with 14 kV three-phase AC, whereby two parallel switched generators feed their power into one transformer. The transformers have beside the two secondary windings required for the realization of the 12 pulse valve bridges a third winding for feeding electric power in the local 220 kV grid. The station has no harmonic filters. All required reactive power is delivered from the generators of the power plant.

Mikhailovska converter station

The converter station in Donbass area, the Mikhailovska converter station, is situated northeast of Pervomaisk, Luhansk Oblast at. Similarly to Volzhskaya converter station, each pole uses four series connected three-phase valve bridges, which form two series connected twelve pulse bridges. As at Volzhskaya converter station one mercury arc valve group was replaced in 1977 by a thyristor valve group. The valves of Mikhailovska converter station are connected through the converter transformers to the local 220 kV grid. Unusually, the DC line crosses the whole AC switchyard of the substation before it enters the valve hall situated at the southern side of the station. The hall is long and has a long wing pointing in south-southwesterly direction. The Mikhailovskaya converter station has three harmonic filters, each with a reactive power of 132 MVA, which are situated northerly of the AC switchyard.

Powerline

The powerline to Donbass area has a length of and the entire length is overhead line.
The suspension towers have a single crossbar, carrying one conductor on a suspension insulator at each end of it.
Two types of strainers are used: lattice towers similar to the suspension towers, but equipped with strainer insulators and of stronger design and much more often pole-type towers with a central pole supported by two diagonal bars. The latter towers carry only one conductor, and there are always 2 such towers close together.
South of Solinky at, there is an unusual double pylon in the line, at which one conductor is fixed at suspension insulators, while the other is fixed with strainer insulators. The exact use of this pylon is unknown. It may carry equipment for extracting PLC-signals from the line, which may be used by Solinky 110 kV substation approximately 1 kilometres northward.
Southwest of Kamennyy between and the line is installed on portal pylons designed for 3 conductors, although the line has there as in all other sections just 2 conductors.
The conductors consist of bundles of 2 ACSR-conductors with 600 mm2 cross section. The whole line is equipped with a single ground wire. It is a single ACSR-wire with 70 mm2 cross section and fixed on the pinnacles of the pylons.
The line leaves Mikhailkovskaya converter station in north-northeast direction. Southeast of Onkhove it turns east-northeasterly. South of Prychiplivka it turns eastwards. East of Krasnyl Lyman it changes its way to east-northeast and passes Schastia northward. North of Petrivka the line runs eastwards and then after Nyznoteple southwards in order not to cross a populated valley. Then at Teple it turns eastwards, however changes its way to east-southeast direction north of Harasmythka. The border to Russia is crossed north of Ushakovka at, but it enters Ukraine again for a very short section south of Talove at. The line runs in Russia past Krasnovka and Novotalovka until Taradinka eastwards, where it turns again toward northeast. North of Krivorzne its direction went more eastwards. In its further track, it passes between Krinychnyy and Melnichnny and runs past Krasnoschekov and Krasnoyarovka through large fields to Varlamovka. In its further track it passes south of Rusakov, south of Kalmykovsky and south of Erik. Behind Erik, its way nears Don River. Short before Don River the line turns to southeasterly in order to cross it in a right angle, The crossing itself, which is situated near Peskovatka at has a span width of. As the west bank of Don River is here a hill, there are no extraordinary tall pylons used.
After Don Crossing it runs the remaining way to Volgograd until a point 5 kilometres east of Kuzmichi, where it meets the 500 kV AC lines to Volgograd Hydroelectric Plant nearly straight eastward. Then it turns southeasterly and south of Erzovka southward. It crosses several areas with recreational garden houses in the northern quarters of Volgograd and passes southerly an industrial complex and the 500 kV switchyard of Volga Hydroelectric Power Plant before it reaches its destination, the inverter plant of Volga Hydroelectric Plant, which is integrated in the power station. One conductor of the line ends at the Western end of the Power Station Building, while the other crosses on the pylons of the 220 kV-powerline, which starts here the building and ends on the other site of the building. This comes from the fact, that the valve groups are switched in series and each valve group is fed by its own machine.

Electrodes and electrode lines

HVDC Volgograd–Donbass can be operated as a monopolar scheme with ground return, therefore two ground electrodes are installed. Both electrodes are designed as land electrodes consisting of a single steel rod with 30 millimetres diameter whereby coke backfill is used.
The electrode lines, which look like a 110 kV-powerlines with 2 conductors, use similar, but smaller pylons as the main line. In opposite to the main line, all strainers are free-standing lattice towers with a single crossbar, while the suspension towers of the electrode line are usually concrete poles with a single crossbar made of steel. Only suspension towers of extraordinary height are built as lattice towers.
The electrode of Mikhailovskaya converter station is situated north of Smile at.
It is connected with Mikhailovskaya converter station by a 32 kilometre long overhead line, which consists of two parallelized 2450 mm2 ACSR conductors.
The electrode line from Mikhailovskaya converter station follows the main line on the left side seen from Mikhailovskaya converter station until a point northeast of Zolobok at where it undercrosses the main line. After this point, it follows the main line on the other site until a point south of Krymske at where it leaves the course of the main line in southeast direction toward the electrode.
The electrode for the terminal at Volgograd is situated northwest of Kamennyy at. It is connected with it by a 24 kilometre long overhead line consisting of two parallelized 2450 mm2 ACSR conductors.

Trivia

Right of way of HVDC Volgograd–Donbass, according to Google-Maps. May be imperfect due to low resolution.

Russia

Ukraine

NumberCoordinates
55
56
57
58
59
60
61
62
63
64

Electrode Line in Ukraine

NumberCoordinates
1
2
3
4
5
6
7
8
9
10
11
12
12A
14
15

Electrode Line in Russia

Incomplete as line cannot be tracked on Wikimapia through Volgograd
NumberCoordinates
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20