Family of Medium Tactical Vehicles


The Family of Medium Tactical Vehicles is a series of vehicles, based on a common chassis, that vary by payload and mission requirements. The FMTV is derived from the Austrian Steyr 12 M 18 truck, but substantially modified to meet U.S. Army requirements, these including a minimum 50 per cent U.S. content.
There were originally 17 FMTV variants—four variants in the nominal 2.5 U.S. ton payload class, designated Light Medium Tactical Vehicle, and 13 variants with a nominal 5 U.S. ton payload rating, called Medium Tactical Vehicle.
Since the first FMTVs were fielded in January 1996 the family has been expanded and the overall design enhanced considerably. The FMTV was originally manufactured by Stewart and Stevenson, then by Armor Holdings, then by what is now BAE Systems Platforms & Services until 2011. It is currently manufactured by Oshkosh Corporation. On 13 October 2016 the U.S. Army solicited proposals for the FMTV A2 rebuy competition. On 7 February 2018 the U.S. Army announced the FMTV A2 contract had been awarded to Oshkosh Defense.

Development and production history

FMTV's origins trace back to a U.S. Army TRAining and DOctrine Command requirements document issued in 1983 for a Medium Tactical Truck, the intended replacement for the in-service 2.5-ton truck. In July 1984 a program to look at a future 5-ton truck procurement to replace in-service 2.5- and 5-ton trucks began. Cost analysis demonstrated that the procurement should be for both 2.5- and 5-ton trucks, and in October 1984 FMTV formally began as a program. The Request For Proposals for FMTV was released in 1988. At this time it was expected that around 120,000 trucks would be ordered over three five-year contracts.
In October 1988, the U.S. Army awarded contracts to Stewart & Stevenson, the Tactical Truck Corporation, and Teledyne Continental Motors for 15 prototype vehicles each, these to be completed by January 1989. In October 1991 a five-year FMTV contract was awarded to Stewart & Stevenson. The initial contract order total was expected to be 20,000 vehicles, but this was reduced to 10,843 vehicles valued at USD1.2 billion. Some options were added and raised the total to 11,197 vehicles over what would be extended to 7 contract years. The first FMTVs were fielded in January 1996.
In October 1998 Stewart & Stevenson was awarded the second FMTV contract, this for 8,000 trucks and 1,500 companion trailers and with a value of $1.4 billion. Total quantities including options were 11,491 trucks and 2,292 trailers, delivered between September 1999 and October 2004. Trucks were the improved A1 model, with improvements including an uprated engine and transmission, and the introduction of ABS. The first A1 models were fielded in July 2000.
Stewart & Stevenson and Oshkosh Truck Corporation were awarded contracts in April 2001 for the Evaluation Phase of the FMTV A1 Competitive Rebuy program for the next FMTV production contract. Following trials and evaluation, in April 2003 the contract was awarded to Stewart & Stevenson. Production of the FMTV A1 CR began in Q3 2004. Improvements to A1R models were numerous and included a new EPA 2004 compliant Caterpillar C7 engine. A total of 21,149 FMTVs and companion trailers were built under the FMTV A1R contract award.
In May 2006, Stewart & Stevenson was acquired by Armor Holdings Inc., and in August 2007, Armor Holdings was acquired by BAE Systems.
The U.S. Army had intended that the Future Tactical Truck System with just two variants would eventually replace virtually all of its tactical wheeled vehicle fleet including the FMTV. FTTS never materialized, however along with inputs from other efforts it continues to be used to define requirements for future U.S. Army trucks. With FTTS already faltering, BAE Systems was awarded a bridging contract in June 2008 for up to 10,000 FMTVs or trailers, the contract including an option for 10,000 additional vehicles.
In May 2009 BAE Systems, Navistar Defense and Oshkosh Defense each announced they had submitted proposals for the FMTV A1P2 competitive rebuy program to the U.S. Army's Tank-Automotive and Armaments Command Life Cycle Management Command. In August 2009, the U.S. Army announced that Oshkosh Defense had been awarded the FMTV A1P2 rebuy production contract. The award was protested by both BAE Systems and Navistar.
The FMTV A1P2 rebuy was awarded as a five-year 'build-to-print' requirements-type award that at award allowed the U.S. government to order from 0 up to 12,415 trucks and 10,926 trailers through to calendar year 2014. Some FMTV variants are excluded from the rebuy competition, those excluded include specialist FMTV variants such as HIMARS, Patriot, MEADS and LVAD, plus all the armored cabs developed by BAE Systems.
According to the U.S. Army all FMTV work with BAE Systems had concluded, BAE Systems and legacy companies having delivered around 74,000 FMTV trucks and trailers to the U.S. Army.
U.S. budgetary projections of March 2012 suggested that due to funding constraints the FMTV program would be terminated in FY14. Under the FMTV contract orders could be placed until December 2013, with first deliveries to commence within one year of that, with final deliveries one year later. Contract extensions have been made and the Justification and Approval notice for the latest of these, which will extend the FMTV contract from 30 September 2016 to 25 August 2019 and will allow for the continued procurement of FMTV A1P2s, was released on 14 October 2016. One day earlier, on 13 October 2016 the U.S. Army solicited proposals for the FMTV A2 rebuy competition.
On 11 January 2017 Israel's Ministry of Defense announced it would be acquiring 200 FMTVs from Oshkosh in a contract valued at $200 million. Deliveries are expected to start this year and conclude mid-2018. The MoD noted that additional orders are likely. At this time Oshkosh confirmed that since deliveries started in 2010, the company had received orders for over 24,500 FMTV trucks and 11,400 FMTV trailers.
On 21 September 2017 Oshkosh announced that the U.S. Army had announced an administrative modification to the FMTV A1P2 requirements contract with the company, this to establish the eighth, ninth and tenth Order Years’ pricing under the contract, at an estimated value of $466 million. This administrative modification authorizes future orders under the FMTV A1P2 contract through August 25, 2019. This contract extension will close out production of the FMTV A1P2.
On 21 September an order for 1,065 FMTVs at a value of $260.1 million under Order Year 8 of the latest contract extension was announced. On 27 September a further two Order Year 8 orders for a total of 148 FMTVs valued at more than $36 million was announced, with Oshkosh also confirming that the company had delivered more than 36,200 FMTV trucks and trailers. On 6 November Oshkosh announced the delivery of the 25,000th FMTV truck to the US Army. On 14 June 2018 Oshkosh announced that the U.S. Army Contracting Command had placed four additional orders for a total of 771 FMTV A1P2s, valued at $159.6 million.
Oshkosh Defense announced on 27 February 2019 that the U.S. Army Tank-automotive and Armaments Command Life Cycle Management Command had placed orders with the company for a further 354 FMTV A1P2 trucks and trailers at a value of $75 million. By February 2019, Oshkosh had delivered more than 38,100 trucks since the award of the FMTV A1P2 contract. On 28 June 2019 the US Department of Defence announced that Oshkosh had been awarded a $320,000,000 modification to domestic and Foreign Military Sales contract W56HZV-09-D-0159 for procurement of Family of Medium Tactical Vehicle variants. Estimated completion date is 24 August 2021.

Technical description and variants

The 2.5-ton FMTV is designated as the Light Medium Tactical Vehicle, while the 5-ton is designated the Medium Tactical Vehicle.
The FMTV is based on the Austrian Steyr 12 M 18 truck, but substantially modified to meet U.S. Army requirements that included a minimum 50% US content. The original 15 FMTV prototypes were assembled in Austria and while based on the 12 M 18 chassis-cab, were fitted with a number of US-supplied/specification components including a Caterpillar diesel engine, Allison automatic transmission and Meritor drive axles.
In a move away from previous U.S. Army designs, a Cab Over Engine design was selected for the FMTV as while the US Army did not specify this configuration, given the Cold War situation prevailing at the time it had indicated that overall length for shipboard transport was a consideration.
On a model-for-model basis the FMTV is around 3 ft. shorter than its bonneted predecessors, while retaining a C-130 Hercules transport capability. Subject to load dimensions, all original FMTV variants are C-130 transportable at GVWR and all models capable of being transported underslung by helicopter are fitted with a sliding outrigger system. Low Altitude Parachute Extraction System, later revised to Low Velocity Air Drop variants of A0 production LMTV and MTV variants were produced.
The chassis and cab of the FMTV feature extensive corrosion protection. It was the first truck to pass the U.S. Army's 22-year accelerated corrosion test.
The design of FMTV has never remained static and to further increase reliability, user friendliness and operational flexibility, detailed refinements/upgrades have continued throughout FMTVs production run.
FMTV is built around a conventional bolted / huck-bolted, cold-formed C-section chassis with bolted-in tubular cross-members. The high-grade 758 MPa steel used is sourced from Sweden. LMTV variants can be fitted with a DP-10J winch with an 11,000 lb. line pull. MTV variants use a DP-515 winch with a 15,500 lbs. line pull.
Current production FMTV A1P2s are powered by a 2007 Environmental Protection Agency emissions compliant 7.2-liter six-cylinder Caterpillar C7 diesel engine developing 275 hp and 860 Lb.-Ft. torque in LMTV variants and 330 hp and 860 Lb-Ft.torque in MTV variants. FMTV A1Rs have a 2004 EPA emissions compliant version of the same engine with the same power output. FMTV A1 variants have an earlier 1998 EPA emissions compliant version of this engine, the 3126 ATAAC which developed 275 hp at 2400 rpm and 815 Lb.-Ft.torque at 1600 rpm in LMTV variants and 330 hp and 850 Lb.-Ft.torque in MTV variants. A 6.6-liter derivative of this engine, the 3116 ATAAC, was fitted to FMTV A0 models where it developed 225 hp and 735 Lb.-Ft. torque in LMTV variants, and 290 hp at 2600 rpm and 860 Lb.-Ft. torque in MTV variants.
The Allison 3070 SP seven-speed transmission fitted to A1P2 and A1R FMTVs has also evolved with the FMTV, its A1 designation being MD 3070 PT, its A0 designation being MD-D7. This has an integral single-speed transfer case. All-wheel drive is full-time, with a 30/70 per cent front/rear torque split for on-road driving, and a 50/50 per cent split for off-road driving.
All FMTV models are fitted with Meritor beam axles, the ratings and specifications of which have also evolved as the FMTV has developed. Suspension is by a combination of parabolic tapered leaf springs, shock-absorbers, and an anti-roll bar for the rear axle/bogie;
Two cargo trailers are part of the Family of Medium Tactical Vehicles. The M1082 single-axle trailer is used with the LMTV cargo truck and the M1095 twin-axle trailer is use with the MTV cargo truck. Both trailers have payloads that match that of the towing truck, and they share many components with the towing truck.

Variants

'
Current and recent operational scenarios now call for logistic trucks of the FMTV type to at least have the option of cab armoring. When it entered production, armoring was not considered an option for the FMTV.
The first protection solution for the FMTV was not in answer to such scenarios, but was developed by Stewart & Stevenson and O'Gara-Hess & Eisenhardt Armoring Company. Called the Crew Protected Cab, it was specifically for the HIMARS variant and offered flash and Foreign Object Debris protection during launch. Designs followed for an Enhanced Crew Protected Cab, and later an Armor Protected Cab, each adding more ballistic capability against direct fire, artillery burst and mines.
To meet emerging threats on deployed operations, in March 2004 DRS Technical Services was awarded a $16.3 million contract to provide 272 armor protection kits for the FMTV. A total of 1,862 kits are understood to have been produced in total. These kits were based around ballistic-protection panels installed on standard FMTV cabs.
In answer to demands for greater crew protection, BAE Systems developed the Low Signature Armored Cab for all variants of the FMTV. The LSAC replaced the standard FMTV cab in a remove and replace operation.
To meet the US Army's current Long Term Armor Strategy for armored cabs, BAE Systems developed the LTAS cab for the FMTV. BAE Systems states that it produced over 9,000 LTAS cabs for the FMTV A1P2 variant. All Oshkosh FMTV vehicles include the company's own LTAS-compliant armor solution.
LTAS is based around the A and B kit principles, this allowing for vehicles to be armored as required, and with the add-on applique package adaptable to prevailing threats and upgradeable as new armoring technologies emerge. The A-Kit, which includes a new cab, modifies the FMTV to allow the addition of armour; the B-Kit being the bulk of the armor itself.
The Caiman Mine Resistant Ambush Protected vehicle is based on the MTV A1R platform. The U.S. Marines placed an initial order with the then Armor Holdings for 1,170 Caiman in July 2007. In total 2,868 Caiman were ordered, with deliveries completed during November 2008. BAE Systems unveiled the Caiman MultiTerrain Vehicle at AUSA in Winter 2010. The Caiman MTV is a modified version of the base Caiman that features a revised driveline, new chassis and upgraded fully independent suspension. BAE Systems received contracts to upgrade 2071 Camian to Caiman MTV standard, these upgrades completed Q1/Q2 2014. Post-Afghanistan no Caiman MRAPs have been retained by U.S. armed forces, although some have been transferred to U.S. law enforcement agencies. Others have been offered as Excess Defense Articles to Iraq, Jordan, Nigeria and the United Arab Emirates.
BAE Systems unveiled the Caiman Light in 2008, a five-man 4x4 version of the Caiman. To meet the Iraqi Light Armored Vehicle Requirement BAE Systems offered a fully armored LMTV on which the LSAC cab was extended rearwards into a troop carrying body. Neither of these proposals entered production.

Prototype and developmental FMTVs

Early in 2014 the U.S. Army's Program Executive Officer for Combat Support and Combat Service Support had suggested that the Army would be seeking a new medium truck family in the mid-2020s. On 13 October 2016 the U.S. Army solicited proposals for the FMTV A2 rebuy competition.
The FMTV A2 request for proposals stated the programme would seek "to integrate higher capacity suspension, wheels, and tires; integrate underbody protection; increase engine power; integrate higher capacity alternator; integrate data bus upgrade; and integrate safety enhancements". The winner of the contract would be asked to integrate such upgrades; build the vehicles, trailers, and kits; and provide programme, maintenance, and logistics support. According to the RfP, the FMTV A2 contract is expected to cover five ordering years with two additional one-year option periods for a potential total of 2,400 vehicles if all options are exercise. In a subsequent statement an Army spokesman said the RfP: "includes an estimated quantity of approximately 2,400 new production vehicles. However, the actual quantities in any future award are undetermined and will depend on proposed pricing for this quantity, army requirements, and available funding."
Oshkosh announced on 8 May 2017 that the company had submitted a proposal in response to the Request for Proposal for Family of Medium Tactical Vehicles A2 production effort. At this point in time the U.S. Army anticipated a contract award announcement in the second quarter of fiscal year 2018, and stated the next generation FMTV A2 would comprise 16 models and three trailers.
The Army announced on 7 February 2018 it had selected Oshkosh to build to FMTV A2. The initial estimated contract value is $476.2 million with no cap on the number of vehicles the Army may purchase. The firm fixed price contract covers a five-year ordering period plus two additional one year options. The estimated date of completion has previously been quoted as February 2022. Both Oshkosh and AM General submitted bids for the requirement. Since receiving the FMTV A2 award, Oshkosh has started building vehicles in support of Production Verification Testing, Live Fire Testing and logistics development. Oshkosh expects the FMTV A2 program to transition to low rate production in FY21.
FMTVs are currently being reset at the Red River Army Depot on return from deployed operations, and current projections are for a Recap program to commence in 2020/2021.

Gallery

Operators

Specific details of FMTV export orders are seldom officially announced, with a large quantity of deliveries covered by assorted US Foreign Military Sales awards.
Djibouti, Lebanon and Romania are three countries listed as possible future recipients of FMTVs in a June 2019 US DoD FMS delivery announcement.