Combined Charging System


The Combined Charging System is a standard for charging electric vehicles. It uses the ' and ' connectors to provide power at up to. These two connectors are extensions of the Type 1 and Type 2 connectors, with two additional direct current contacts to allow high-power DC fast charging.
The Combined Charging System allows AC charging using the Type 1 and Type 2 connector depending on the geographical region. Since 2014 the European Union has required the provision of or within the European electric vehicle network. This charging environment encompasses charging couplers, charging communication, charging stations, the electric vehicle and various functions for the charging process as e.g. load balancing and charge authorization.
Electric vehicles or electric vehicle supply equipment are CCS-capable if they support either AC or DC charging according to the standards listed by the CCS. Automobile manufactures that support CCS include: BMW, Daimler, FCA, Ford, Jaguar, General Motors, Groupe PSA, Honda, Hyundai, Kia, Mazda, MG, Polestar, Renault, Tesla and Volkswagen Group.
In the United States, BMW and VW claimed in April 2016 that the East Coast and West Coast corridors had "complete" CCS networks. Competing charging systems for high-power DC charging include CHAdeMO, Guobiao recommended-standard 20234, and Tesla Supercharger.

History

The spurred deployment of charging stations. Initially, these accessed the abundant AC mains electricity using a variety of plugs around the world. The standardization in IEC 62196 for higher-current charging connectors brought about various systems: Type 1 was used primarily in North America and Japan, and Type 2 variants elsewhere. For DC charging, the SAE and European Automobile Manufacturers Association made a plan to add common DC wires to the existing AC connector types such that there would be only one "global envelope" that fitted all DC charging stations.
The proposal for a "Combined Charging System" was published at the 15th International VDI-Congress of the Association of German Engineers on 12 October 2011 in Baden-Baden. CCS defines a single connector pattern on the vehicle side that offers enough space for a Type 1 or Type 2 connector, along with space for a two-pin DC connector allowing charging at up to 200Amps. Seven car makers agreed to introduce CCS in mid-2012. The prototype implementations for up to 100 kW were shown at EVS26 in Los Angeles in May 2012. DC charging specifications in the IEC 62196-3 draft give a range up to 125 A at up to 850 V.
The seven auto makers also agreed to use HomePlug GreenPHY as the communication protocol. The prototype for the matching plug was developed by Phoenix Contact with the goal to withstand 10,000 connect cycles. The standardization proposal was sent to the IEC in January 2011. The request to use a PLC protocol for the Vehicle2Grid communication was flagged back in September 2009 in a joint presentation of BMW, Daimler and VW at a California Air Resources Board ZEV Technology Symposium. This competed with the CAN bus proposal from Japan and China, and none of their car manufacturers has signed up to CCS. However, China had been involved in early stages of the development of the extra DC pins.
Volkswagen built the first public CCS quick-charge station providing 50 kW DC in Wolfsburg in June 2013 to test drive the upcoming VW E-Up that is to be delivered with a DC rapid charger connector for CCS. Two weeks later, BMW opened its first CCS rapid charge station to support the upcoming BMW i3. Since at least the second EV World Summit in June 2013, the CHAdeMO association, Volkswagen and Nissan all advocate multi-standard DC chargers, as the additional cost of a dual-protocol station is only 5%.
In Germany, the Charging Interface Initiative e. V. was founded by car makers and suppliers to promote the adoption of CCS. They noted in a press release that most cars cannot charge faster than 50 kW, so that was the first common power output of CCS stations to be built during 2015. The next step was the standardization of stations with 150 kW output that they showed in October 2015, looking to a future system with 350 kW output. Volvo joined CharIN in 2016; Tesla in March 2016; Lucid Motors June 2016; Faraday Future June 2016; Toyota in March 2017.
The Chevrolet Bolt/Opel Ampera-e uses this CCS standard for 55 kW quick charging.
As part of the 2016 settlement of the Volkswagen emissions scandal, VW is to spend $2 billion in the United States over the following 10 years on CCS and other charging infrastructure through subsidiary company Electrify America. In this effort, charging stations will be built with up to 150 kW at community-based locations and with up to 350 kW at highway locations. Besides CCS, CHAdeMO charging stations will be constructed.
In November 2016, Ford, Mercedes, Audi, Porsche and BMW announced building a 350 kW charge network with 400 stations in Europe, and priced at €200,000 each.

Versions of the specifications

The Combined Charging System is meant to develop with the needs of the customer. Version 1.0 covered the currently common features of AC and DC charging, and version 2.0 addressed the near to midterm future. The specifications and underlying standards for CCS 1.0 and CCS 2.0 are described for DC charging in Table 1 and for AC charging in Table 2.
The automotive manufacturers supporting CCS committed themselves to migrate to CCS 2.0 in 2018. Thus it is recommended for charging station manufacturers to also support CCS 2.0 from 2018 onwards.
The specifications of CCS 3.0 were not yet precisely defined. All features of previous versions shall be preserved to ensure backward compatibility. Potential additional features include:
Unlike the connector and inlet, which depend on the geographical location, the charging communication is the same around the globe. Generally two types of communication can be differentiated.
CCS differentiates between two methods of load balancing.
For charge authorization, generally two approaches are foreseen.
The vehicle coupler is composed of the vehicle connector, which is mounted at the end of a flexible cable, and the vehicle inlet, the counterpart of the connector, which is located within the vehicle. The CCS couplers were based on the Type 1 coupler, the North American standard, and Type 2 coupler, the European standard, as described in IEC 62196-2. One of the challenges of the Combined Charging System was to develop a vehicle inlet which is compatible with both the existing AC vehicle connectors and additional DC contacts. For both Type 1 and Type 2 this has been accomplished by extending the inlet with two additional DC contacts below the existing AC and communication contacts. The resulting new configurations are commonly known as Combo 1 and Combo 2.
For the DC vehicle connector, the implementation varies slightly between Combo 1 and Combo 2. In the case of Combo 1 the connector is extended by two DC contacts, while the Type 1 portion of the connector remains the same with the AC contacts being unused. For Combo 2 the AC contacts are completely removed from the connector and therefore the Type 2 portion of the connector has only three contacts remaining – two communication contacts and a protective earth. The vehicle inlet may retain AC contacts to allow non-CCS AC charging.
In both cases, communication and protective earth functions are covered by the original Type 1 or 2 portion of the connector. The Type 1 and Type 2 connectors are described in IEC 62196-2, while the Combo 1 and Combo 2 connectors are described in IEC 62196-3 as Configurations EE and FF.
Inlet connectorType 1Combo 1
Type 1
AC charging, single phase
Does not mate
Combo 1
AC charging, single phase
DC charging

High-power charging

As vehicle couplers for DC charging according to IEC 62196-3:2014 Ed.1 allow DC charging only with currents up to 200 A, they do not sufficiently cover the needs of the future charging infrastructure. Consequently, a later edition of the standard supports currents of up to 500 A. Such high currents, however, either require large cable cross-sections, leading to heavy and stiff cables, or require cooling if thinner cables are desired. In addition, contact resistance leads to more heat dissipation. To cope with these technical issues, the standard IEC TS 62196-3-1 describes the requirements for high-power DC couplers including thermal sensing, cooling and silver-plating of contacts.

Global acceptance

The Combined Charging System is primarily driven by European and North American car manufacturers. Type 1 and Combo 1 chargers are primarily found in North and Central America, Korea and Taiwan, while Type 2 and Combo 2 can be found in North and South America, Europe, South Africa, Arabia, India, Oceania and Australia. For DC charging the competing standard GB/T is used in China, while Japan uses CHAdeMO. In many remaining countries no standard is preferred yet, however, a recommendation from CharIN is to use Type 2 and Combo 2. In the European Union according to Directive 2014/94/EU all high-power DC charging points installed after November 18, 2017 shall be equipped for interoperability purposes at least with Combo 2 connectors. However, this does not prohibit the provision of other charging points using e.g. CHAdeMO or Tesla Superchargers.