Chevrolet Camaro (fifth generation)


The fifth-generation Chevrolet Camaro is a pony car that was manufactured by American automobile manufacturer Chevrolet from 2010 to 2015 model years. It is the fifth distinct generation of the muscle/pony car to be produced since its original introduction in 1967. Production of the fifth generation model began on March 16, 2009 after several years on hiatus since the previous generation's production ended in 2002 and went on sale to the public in April 2009 for the 2010 model year.

Development

By spring 2005, the first concept car of the fifth-generation of the Camaro was in development. Several sketches of both exterior and interior were drawn to resemble of how the car was going to look, these sketches were shown months later to the public. Once sketches were finished, the Camaro was constructed as a clay model which was complete by fall 2005 and was shown to the public in early 2006.
After the public introduction of the concept cars, Chevrolet started constructing several camouflaged test mules of the Camaro which were manufactured by Holden costing about US$250,000 each. These vehicles were used for crash testing, test driving, and to handle extreme weather conditions such as in Canada, Arizona, and Australia. By January 2008, Chevrolet announced that the test mules will not be camouflaged and various images of the Camaro were released in the same year, including pre-production models.

Pre-production concept vehicles

Chevrolet Camaro Concept (2006)

The Chevrolet Camaro Concept was designed by a South Korean-born designer Sangyup Lee. The car was based on the Holden developed GM Zeta platform. It was powered by a 6.0-liter LS2 V8 engine rated at with active fuel management. The engine was mated to a T56 6-speed manual transmission and the car was equipped with front and rear suspension featuring progressive-rate springs and gas-pressurized dampers, four-wheel vented disc brakes with 14-inch rotors, 21-inch front and 22-inch rear five-spoke cast alloy wheels, and 275/30R21 front and 305/30R22 rear tires. The wheelbase is, which is longer than its predecessor, but an overall length of just, shorter. The concept was inspired by the 1969 Camaro.
The Camaro concept was unveiled at the 2006 North American International Auto Show.
AutoWeek editors unanimously awarded the Camaro Concept "Best In Show."

2007 Camaro Convertible Concept

The 2007 Camaro Convertible Concept was announced on January 6, 2007 at the 2007 North American International Auto Show. Early speculation on the existence of the car by many automotive publications proved to be true when an early embargo was broken on January 4, 2007.
At a glance it would seem that the only difference between the coupé and convertible concepts would be the roof and Hugger Orange pearl tri-coat paint job with a pair of dark gray racing stripes, but this was not the case. Besides the obvious convertible top, there were subtle changes to the exterior as well. Every surface was changed from the door-cut back. The rear fenderlines dropped off from the horizontal surface to the vertical surface a couple of inches farther out than on the coupé to maintain visual proportions. The rear spoiler was also reshaped. The front and rear wheels were redesigned and a thin orange line was applied to the outer edge, a nod to the redwalls available on the 1969 Camaro.
There were many interior changes that were incorporated into the new concept. The retro houndstooth-pattern seats of the coupé were replaced with modern leather and orange stitching. The metal finishes, accent panels, and seats were all in different colors. The rear seats were closer together to make room for the tonneau cover. The clarity of the circular gauges in square frames were improved by making the faces white with black chrome numbers and a red anodized needle. The deep-dish three-spoke steering wheel and four-pack gauge cluster were carried over from the coupé concept. Chrome seat-belt buckles were designed to look like the iconic belts buckles in late 1960s GM automobiles. This reworked interior of the Camaro Convertible Concept was a very close representation of what would be seen in the production version of the vehicle.

2008 SEMA concepts

General Motors showed several concept variants of the production version of the Camaro on November 3, 2008 at the 2008 SEMA show.

Camaro Black

The Camaro Black Concept featured a matte black hood, tinted glass, HID headlamps with red "halo rings," a darker grille, dark-tinted taillight lenses, and wheels with a darker finish. The interior also featured the same black theme as the exterior. It was powered by the V6 engine.

Camaro LS7

Inspired by the COPO Camaros of the late 1960s, the Camaro LS7 Concept was built from the 2010 Camaro SS with the LS3 engine replaced with a GM Performance Parts 7.0-liter LS7 crate motor having a power output of. The heritage of COPO's performance history was reflected with the inclusion of a high-performance exhaust and improved headers, air intake system, and camshaft—all developed by GM Performance Parts. Other modifications included a Tremec six-speed manual transmission, Brembo brakes, Hurst short-throw shifter, 20-inch custom wheels, and a lowered ride height. The exterior of the car was finished in Victory Red with accents of matte black on the "LS7" badges, front grille slot, rear headlight panel, and hood. The LS7 logo was repeated in Victory Red on top of the hood cowl. The interior had a matching color scheme with red panel trim on the doors, dash, and gages. Gloss black replaced every trim that came in silver in the final production Camaros, such as on the steering wheel, shifter knob, vent trimmings, and center console clusters.

Dale Earnhardt Jr. Camaro

The Camaro Dale Earnhardt Jr. Concept was produced with input from NASCAR Race driver Dale Earnhardt Jr. The Camaro started life in SS trim and was tuned to run on higher-octane E85 fuel. It featured a gray and white paint scheme with orange trim. Additional features included five-spoke wheels, a dovetail spoiler, alternate grille, and other official GM accessory modifications.

2010 Chevrolet Camaro GS Racecar Concept

The Camaro GS Racecar Concept design was inspired by Mark Donohue's blue-and-yellow Trans Am Series Camaro. It features a carbon fiber hood, trunk lid, doors and fenders to keep weight down and is powered by an LS3 V8 engine mated to a Tremec TR-6060 six-speed manual transmission. Additional racing modifications included a exhaust with Coast Fab mufflers, C&R racing aluminum radiator, and coolers for the engine oil, transmission, and differential. It was designed for use in the KONI Challenge Series.
The concept vehicle went on sale by Mecum Auctions during the 2013 Monterey Car Week.

2010 model year

On August 10, 2006, GM Chairman and CEO Rick Wagoner announced that the company would build an all-new version of the Chevrolet Camaro based on the award-winning concept that debuted at the 2006 Detroit auto show in January 2006. The new Camaro was originally scheduled to begin production in 2008 and to go on sale in the first quarter of 2009 for the 2009 model year, but General Motors stated in March 2008 that production would be delayed until February 2009 with the Camaro going on sale in the spring of 2009 for the 2010 model year.
Chevrolet General Manager Ed Peper stated that the new Camaro "will appeal to both men and women, and unite customers with fond memories of previous Camaros with those who first experienced a Camaro" when the concept was unveiled in January 2006. Bob Lutz's post on the GM FastLane Blog for August 10, 2006 thanked everyone in the blogosphere who commented and offered feedback on the Camaro.
Following the development of the Zeta architecture and because of its position as the GM global center of RWD development, GM Holden in Australia led the final design, engineering, and development of the Camaro. Original plans for the car included sharing the chassis with the Impala, which was to be switched to the Zeta platform. However, a 2007 energy law drastically changing the Corporate Average Fuel Economy forced GM to scuttle plans for replacing the W-Body platform of the Impala. The new Camaro was produced at the Oshawa Car Assembly manufacturing plant in Canada. 2,750 jobs would have been lost at the Oshawa manufacturing plant which had been originally scheduled to be closed in 2008; some of these jobs were saved due to the new Camaro's production. This new product program and conversion of the Oshawa plant to a state of the art flexible manufacturing facility represented a US$740,000,000 investment.

Camaro (2009-2015)

The Camaro was made available as a coupé in five different trim levels; the LS, 1LT, 2LT, 1SS, and 2SS. The LS and LT trim levels are powered by the GM LLT V6 engine having a power output of at 6,400 rpm and of torque at 5,200 rpm. The SS with manual transmission is powered by the 6.2 L GM LS3 V8 engine rated at at 5,900 rpm and of torque at 4,600 rpm while the SS with automatic transmission is powered by a new variant of the LS3 called the GM L99 which produces at 5,900 rpm and of torque at 4,300 rpm. The L99 V8 engine, not to be confused with the earlier LT-series L99, uses Active Fuel Management which enables the engine to run on only four cylinders during urban driving conditions, such as highway cruising, to improve fuel economy.
Other features include a fully independent four-wheel suspension system, variable-rate power steering, four-wheel disc brakes standard on all models, a StabiliTrak electronic stability/traction control system, Competitive/Sport modes for the stability system offered on SS models, launch control on SS models equipped with the six-speed manual transmission, and 6 standard air bags that include head curtain side-impact air bags and front seat-mounted thorax side air bags. An RS appearance package was available on LT and SS trim levels which included HID headlamps with integrated halo rings, a rear spoiler, and RS-specific taillamps and wheels. Rally and hockey stripe packages were made available in several colors as well.


The Camaro was unveiled at the Warren Technical Center, followed by GM Holden's Melbourne headquarters, Yokohama Red Brick Park,
and Summer Sonic 2010.
US models went on sale in the first quarter of 2009.
Japan models included the LT and SS, and went on sale in 2009-12-05.

Transformers Special Edition

On July 22, 2009, GM announced a Transformers Special Edition appearance package for the 2010 Camaro at the 2009 San Diego Comic-Con. The appearance package could be applied to LT and SS trims with or without the optional RS package and could only be applied to orders made in the Rally Yellow exterior scheme. The package included an Autobot shield badge on the driver and passenger side fenders underneath the Camaro nameplate, Autobot shield on each of the four wheel's center cap, Autobot shield embroidered on interior center console, Transformers logo on driver and passenger doors' sill plates replacing the original "Camaro" labeled plates, and high-gloss black center rally stripes with the Transformers ghost logo embedded. This then made the 2010 Camaro resemble the Bumblebee Camaro from the 2007 movie, often referred to as T1 Bumblebee. Production of the add-on package ceased on January 12, 2010 with an estimated 1,500 units produced. 1,916 units were finally produced at the end of 2010.
Japanese models of the ten package went on sale on in February 2010.

2009 SEMA concepts

Jay Leno Camaro

A customized Camaro was built by GM for TV presenter Jay Leno, and is powered by the direct-injected V6 similar to the unit that resides in standard LS and LT models, but has an additional pair of Turbonetics T-3 turbochargers. The engine has a power output of with the help of a custom air-to-air intercooler that feeds 7 pounds of boost pressure into the engine. The extra performance is added with virtually no penalty in fuel economy. Besides the power upgrades, the vehicle also gets an upgraded Centerforce clutch and pressure plate for the six-speed manual transmission, an upgraded Be-Cool radiator, Brembo 6-piston brake package, a Pedders coil-over lowering kit, and a bodykit that includes a new rear diffuser as well as a revised front fascia and hood with additional vents for the brakes and engine.

Synergy Camaro

The Synergy Concept Camaro was one of two concepts that showcased GM accessories that could be applied to the Camaro, previewing a new Synergy Green production exterior color which featured the latest in Camaro appearance accessories offered through Chevrolet dealers in 2009 and demonstrated the personalization possibilities that were open to Camaro owners. The Synergy Concept included Cyber Grey rally hood and rear deck stripes, new ground effects kit consisting of a new rear diffuser, a front spoiler, a new rear bumper with integrated exhaust system and a rear high wing. All accessories that were displayed on the concept Camaro were finished in the production Cyber Grey exterior color. The concept vehicle also included wheels with a black center finish and polished rim. The concept was further enhanced with a Pedders coil-over lowering kit and a set of large Brembo brakes. The interior is color-coordinated with Jet Black and Synergy Green accent stitching, piping, interior trim kit and green ambient lighting that run along the door panels and speedometers. The production version of the concept Camaro, the Synergy Special Edition would eventually be made available in February 2010 through May 2010 in limited numbers.
Japanese models went on sale in February 2010 through May 2010.

Chroma Camaro

The Camaro Chroma Concept is based on an LS3 SS/RS model in Summit White and uses a combination of accessory components that showcased future GM accessories for the Camaro which would become available during the 2011 model year. The Chroma concept was the preliminary design of what would become later known as the "Synergy Series Camaro" that would debut at the 2010 SEMA Show. The accessories package included a new silver stripe package, wheels with silver-painted spoke centers with a Victory Red stripe painted along the edge of the wheel, "Blade” rear spoiler, color-matching ground effects package, rear fender vent graphics, and "Heritage" front grill with body-color outer frame. The interior comes with black and gray leather seats which feature red accent stitching that is also applied to the steering wheel and shifter boot that is surrounding a Hurst short-throw shifter as well as an interior trim kit painted in Silver Ice that incorporates the door panels and dash trim. Mechanically, the car is equipped with a combination of General Motor Performance Parts off-road shorty headers, Pedders' suspension kit, off-road exhaust and Brembo Calipers painted in Victory Red.

Camaro Dusk

The Camaro Dusk Concept offers a contemporary tuner aesthetic featuring an aggressive look, a lowered ride height, BBS wheels, the rear spoiler from an SS model and a custom ground effects package. The ground effects package includes a front splitter, rocker extensions, and a rear diffuser. The car is painted in Berlin Blue while the ground effects are painted a contrasting color. GM added a new exhaust system and Brembo brakes from a Camaro SS. The interior is trimmed in Jet Black and Sedona. Other interior features including footwell lighting and premium door sill plates. The concept also features advanced technology and premium audio options such as a Boston Acoustics sound system, WiFi connectivity, and cradle for an iPhone.
Chevrolet launched a graphics campaign in October 2009 asking Camaro enthusiasts to vote for their favorite design from several accessory graphics packages. The top four designs were produced and brought to the SEMA Show. The Camaro Graphics Concept wore those designs in different days. When the convention ended, another round of voting would be conducted and the winner was considered for future production. Brent Dewar, vice president of Chevrolet, said that "Camaro has thousands of fans on the social media sites and that this is one way for the company to stay connected to its customers."

Synergy Special Edition

On January 14, 2010, GM announced the production version of the Synergy Concept Camaro originally shown at the 2009 SEMA show. The Synergy Special Edition for the 2010 model year is based on the Camaro 1LT/2LT model and features the limited Synergy Green exterior color scheme. Though the edition is from the SEMA concept there are certain accessories that did not come on the production unit such as the high wing spoiler, Black painted wheels and ground effects kit. The production units came accented by Cyber Grey Rally Stripes running the length of the Camaro hood and rear deck. Other exterior features include a standard rear spoiler found on RS and SS packages replacing the high wing and standard Sterling Silver painted wheels wrapped with P245/50R19 tires, backup radar and a sunroof. The color scheme is carried over on the interior with a Synergy Green instrument panel and door inserts with green ambient lighting that run along the door panels. Synergy Green stitching also accents the Jet Black cloth seats, steering wheel, shift knob, and center console. Other standard features include paddle shifters, the Convenience and Connectivity Package which offers Bluetooth phone connectivity, a USB port for MP3 players, and remote vehicle start for models equipped with an automatic transmission. Though this edition of the Camaro has certain accessories that come available with the RS package, the RS package itself was not available to purchase with the Synergy Camaro order. The Synergy Special Edition was available in limited production from February 2010 to May 2010, a total of 2425 were sold.

2010 Indianapolis 500 Pace Car Special Edition (RPO Z4Z)

In April 2010, General Motors and the Indianapolis Motors Speedway announced limited production of the Pace Car that was introduced to pace the 2010 Indianapolis 500. The Indianapolis 500 Pace Car replica is based on the 2010 Camaro 2SS Automatic 400 hp 6.2 L V8 model with RS package which includes the Inferno Orange exterior paint scheme with White Diamond rally stripes that run from front to the rear of the entire body of the car. The event and organization logos of the Indianapolis 500 Speedway are decaled on both driver and passenger doors with special badging placed underneath both front quarter panels of the Camaro nameplate. Special event stitching of the 2010 event replaces the "SS" stitching on the headrests of the front interior seating, with special premium accented floor mats and Inferno Orange accented interior trim kit. The front grille is replaced with the heritage grille that was made available as an aftermarket accessory from GM, with the addition of an Inferno Orange trimmed engine cover. Production was limited to 294 units, the majority of which were produced in automatics and a few had manual transmissions. Out of the 294 units, 50 were sent to the Indianapolis 500 event which could be seen during Pole Day prior to the event with each darning a license plate reflecting its number from 1-50. 45 other units were sent to Canada and 199 were sent to the 186 top Camaro selling dealerships based upon retail sales in the United States.
Production of the 2010 Camaro Z4Z began half-way through the 2010 model year. The production of the 2010 Camaro was temporarily halted in April 2010 when all 294 of the Z4Z models were produced. After the 294 Z4Z models were produced, production of the standard models resumed.
The 2010 Camaro 2SS Indy 500 Pace Car is the second lowest production number Camaro pace car has been made available for public purchase since its debut at the Indianapolis 500 in 1967.

SLP Performance ZL550/ZL575 Special Edition

The SLP Performance ZL550 and ZL575 are limited production versions of the 2010 Chevrolet Camaro SS from SLP Performance. The ZL550 would have a supercharger attached to the 6.2 L V8 boosting power from 426 to 550 hp. The 550 hp variant was mated to the 6-speed automatic transmission. It would also include 20-inch 5-spoke red line machined spoke face with ZL center caps. A decal on the rear tail light in flat black. Heritage style SS badges on the front grill and rear panel, three ZL550 or ZL575 OEM-styled exterior badges, ZL550 or ZL575 logo embroidered in the headrests and floor mats. It also included a 1-250 numbered plaque on the dashboard and numbered key fobs. It also sported a cold air induction system and an axle-back exhaust system with unique tips. A tweaked suspension lowered the front by 1-inch the rear by 0.8-inch. The hood of the car utilizes an RTM hood with a functional heat extractor. The ZL575 used the same 6.2 L V8 upgraded with the ZL550's supercharger rated at 575 hp. The ZL575 models came mated to the 6-speed manual transmission found in the normal Camaro but was tweaked to be able to handle the increased power. An option for the ZL575 was the 6-speed manual transmission would be installed with the clutch off of a Corvette ZR1 for sportier gear changes. Also, an option for the ZL550's transmission was being equipped with a 3:45 gear ratio. Brembo brakes were also an option. Sales began at Chevy dealers in mid-2010.

Styling Special (2010-)

The Camaro Styling Special is a version of the 2010 Camaro LT RS and SS RS for the Japan market. It features a rally stripe, front grille, door sill plate.
The vehicles went on sale in 2010–09.

Motorsports

Stevenson Motorsports entered two Camaros in the Continental Challenge Gran Sport class. They entered one Camaro in the 2009 race at Virginia International Raceway. It was driven by Jeff Bucknum and David Donohue, sons of Ronnie Bucknum and Mark Donohue. Ronnie and Mark were the drivers of the original Trans Am Camaro. John Stevenson confirmed during the Montreal round of the 2009 Rolex Sports Car Series season that Pratt & Miller are working on GT Camaros to replace the Pontiac GXP.R. Stevenson Motorsports will be entering Camaros in the 2010 Rolex Sports Car Series season. The drivers would be Andrew Davis, Robin Liddell, and Jan Magnussen for the #57 car and Mike Borkowski and Gunter Schaldach for the #97 car.
TC Motorsports entered two Camaros in the Continental Challenge for the 2010 season. Also entered is the aforementioned Sunoco Camaro, which debuted in the final round of the 2009 season.
NASCAR uses the Camaro in one of its three national touring series, the Xfinity Series. Drivers who race the Chevrolet SS in the sport's top level, the Sprint Cup Series, also drive the Camaro in the Xfinity Series, including Dale Earnhardt Jr. The Xfinity Series also uses the Ford Mustang and Toyota Camry.

Production

Assembly of the fifth-generation Camaro took place in Canada like its predecessor. Production, however, was shifted from Sainte-Thérèse, Quebec to Oshawa, Ontario.
Chevrolet started taking pre-orders for the 2010 Camaro on October 13, 2008, however sales to rentals and orders made after the pre-order period, were processed before many of the pre-orders. By the end of 2008, General Motors confirmed more than 10,000 advanced orders and that all pre-orders would be completed by October 2009. Camaro sales began in April 2009.
On January 17, 2009, the first production Camaro was auctioned at the 2009 Barrett-Jackson Collector Car Auction in an American Heart Association charity lot. The vehicle was purchased by Hendrick Motor Sports CEO Rick Hendrick for.
By late June 2009, Chevrolet dealers were reporting that the Camaro sales were exceeding availability, with prices running about above the MSRP. It was suggested that this may be influenced by the prominent presence of the vehicle in the that was released worldwide through the month.
General Motors sold 61,648 Camaros in the 2009 calendar year. Sales of the Camaro did not start until April 2009.

Marketing

A 2010 Camaro was shown while the main character was driving in the NBC series My Own Worst Enemy, which premiered on October 13, 2008, as part of a marketing arrangement between GM and NBC.
As part of the 2010 Camaro launch in Japan, a special GM-made T-shirt was made available between July 9, 2009 and August 31, 2009.
As part of the 2010 Camaro launch in Japan, a promotion movie for Camaro was premiered in Altavision Ginza between November 1, 2009 and November 8, 2009.
As part of the 2011 Camaro launch in Japan, new members joining Hooters Tokyo between October 25, 2010 and November 30, 2010 could win a 2010 Chevrolet Camaro LT RS.

2011 model year

Camaro coupe (2010)

For the 2011 model year, the Camaro V6 engine was rated at and, an increase of and from 2010. No engineering changes were made for the increase as GM claimed the in the 2010 Camaro's engine was a conservative rating.
The Synergy Green color from the 2010 Special Edition would be available on all 2011 model trim levels. A head-up display with most of the instrument panel's information would be offered. The HUD is a modified version of the Chevrolet Corvette's display. The main difference is that the version in the Corvette is able to display lateral g-forces, while that amenity is not available on the Camaro.
The Japanese model was unveiled in golf courses in Tokyo, Yokohama, Nagoya, Osaka. Japanese models include LT RS and SS RS with 6-speed automatic transmission and the choice of 9 body colors.

Camaro SSX (2010)

Unveiled at the 2010 SEMA show, the Camaro SSX concept car is a variant of the Camaro SS converted into a closed-course track car, built to showcase new performance parts. The car was developed with input from Pratt and Miller, Chevrolet's partner in Corvette Racing, and Riley Technologies using parts proven in the Grand Am racing series.
Changes over the standard Camaro SS included low-gloss Icy White Metallic body color with red accents and door graphics, carbon fiber hood, fenders, door and deck lid; exposed carbon fiber front splitter, rockers and adjustable rear wing; unique lower grille and brake ducts, removal of carpeting, sound deadening and rear seats; Ace suede-covered racing steering wheel and shifter, SCCA-approved roll cage and window net, racing driver's seat with five-point harness, racing pedals, fire suppression system, racing fuel cell, a video camera system mounted on the roll cage, the LS3 6.2 L V8 engine enhanced with Chevrolet Performance Parts' camshaft, cylinder heads and dry-sump oiling system; six-speed manual transmission equipped with a twin-disc clutch shared with the Corvette ZR1, low-restriction air induction and exhaust systems, 4-wheel disc racing braking system with six-piston front/four-piston rear calipers with drilled and slotted rotors, modified production suspension with Pfadt licensed components and 20-inch racing wheels and tires.
The car received two awards at SEMA: The SEMA Award: Hottest Car and the Gran Turismo Award: Best Domestic.

Neiman Marcus Edition

On October 19, 2010 at 12:00 noon EDT, orders of the Neiman Marcus Edition Camaro Convertible were opened through Neiman Marcus and sold out within three minutes becoming one of quickest-selling special edition vehicles that General Motors has put out in the market. A total of 100 units were produced and deliveries began in early 2011. The NM Camaro was based on both the 1SS and 2SS models and was equipped with the 6.2 L V8 engine in both options of either manual or automatic transmissions with the equal fuel efficiency and power output of the 2011 Camaro. Accessories that separated this edition from the rest were noticeably that of the exclusive tri-coat exterior paint called "Deep Bourdeaux" with ghosted rally stripes spanning across the hood to the rear deck along with a separate "Silver" painted windshield surround. A two-toned interior leather trim also separated the special edition from the rest with basic black leather with "Amber" interior accents on the front and rear seats as well as on the armrests all with accented "Brilliant Red" stitching on the aforementioned including the center console, steering wheel, and shift knob. A black interior trim kit placed upon the doors panels and dash which replaced the standard "Midnight Silver" that came in standard 2LT and 2SS models. 21" five-spoke wheels that were not yet released to the general public for separate purchasing until late 2011 were placed wrapped with Pirelli P-Zero tires that also contained a Brilliant Red strip flowing along the outer edge of the wheel to follow that stitching in the interior. This edition of the Camaro was the only batch of units that were to follow trimming keys of that from the 2007 Camaro Convertible Concept with the Silver painted Window surround, interior leather trim placements, and wide spoke wheels. No Camaro Convertibles produced from the factory ever provided a different color windshield surround other than the produced body color.

Convertible (2011-2015)

Production of the 2011 Camaro Convertible began on January 31, 2011 in Oshawa, Ontario, where the coupé was assembled. It arrived in dealerships in February, and is available in both base and SS versions like the coupe.
US models include a choice of V6 and V8 engines, Tremec TR-6060 6-speed manual or Hydra-Matic 6L50 6-speed automatic transmission, and went on sale in 2011–12.
Japanese models include a choice of four base and two premium body colours. They went on sale on 15 July 2011.

2011 Synergy Series

From concept to reality, the 2011 Synergy Series Camaro first made its debut at the 2009 SEMA event as a concept under the tag of Camaro Chroma. This concept was to display a combination of various parts from the Chevrolet Camaro's accessories catalog of both current and conceptual pieces to provide a different appearance from the other Camaro models. In 2010, the car would pop its face again however under a different exterior paint scheme of "Cyber Gray Metallic" and new nameplate of Synergy Series. It was made known that the Synergy car being shown at the 2010 SEMA event was not just going to be a concept but that it would be made available to the general public to purchase for the 2011 year model run. On May 5, 2011 orders were open to those who desired to purchase the appearance package on top of the price of either a 2LT or 2SS in either a coupe or convertible plus purchase of the RS package was required. Only the exterior colors of Victory Red, Summit White or Black could be made with purchase. Upon ordering the Synergy Series Camaro people had the option to choose between two different packages:
Level One : Red interior stitching on gray leather-appointed interior seats, center console, steering wheel, shifter boot and knob, and armrests on the doors. Switchblade Silver interior trim kit on dash and door panels with accented red light piping in door trim, footwells, and cup holders. Body colored ground effects, Heritage grille, Blade spoiler, and antenna. Red engine cover and red-colored Brembo brake calipers. Premium floor mats with red edging and Silver stripe Yenko inspired decals on hood, mailslot, rear deck, and side gills.
Level Two : All Content from Level One package with the addition of dealer-installed 21” wide five-spoke wheels with "Blade Silver" inserts and "Red Flange" stripe along the edge of wheels.
Only 500 units of this package incorporated into the Camaros were to be produced for the 2011 model year run, however, only 400 were actually ordered. The name Synergy was decided by Chevrolet to be not only known for the green color of the first run of special edition Camaros in 2010 but to be a yearly special edition Camaro offered by Chevrolet for their determination to release at least two special edition Camaros every year. So the word "Series" was added to reflect the editions as an annual special edition.

XM Accessory Appearance Package

The XM Accessory Appearance Package was introduced at the 2010 SEMA event providing an option that would differentiate the 1LT model from the rest as special editions were being offered towards the SS models. Ordering of the appearance package began on February 17, 2011 until the end of the 2011 model and were only limited to the following exterior colors of Black, Cyber Gray Metallic, and Imperial Blue Metallic. Integrated with the purchase of the XM Accessory Appearance Package were front body colored Heritage Grille, 21-inch diameter 5-spoke polished aluminum wheels, Silver strip running along the side of the Camaro following the contours of the shoulders to the front with pinstriping, premium carpeted floor mats, rear spoiler without the need to purchase an RS package and a 12-month free trial subscription to XM Satellite Radio.

Production

Production of the 2011 Camaro began on 2010-06-07.

Marketing

As part of the 2011 Camaro launch in Japan, a Camaro 2-day campaign took place between July 1, 2010 and September 30, 2010, featuring a 2-day test drive chosen by raffle from Chevrolet dealers.
After the 2010 version incarnation of Hawaii Five-0 was picked up by CBS for broadcast, starting with the second episode, a Chevrolet product placement deal includes a Camaro RS used by Danny Williams used for the first three seasons, with a 2014 Camaro replacing it for Season 4. A second Camaro, in yellow, is used by Max Bergman, starting in the second season.
The Chevrolet Camaro was launched in China in April 2011 through imports under the Legend trim level. The 3.6 litre LGX V6 was the standard engine paired to a 6 speed automatic gearbox. Imports for the fifth generation Camaro ended in 2015.

2012 model year update

Camaro, RS, 45th Anniversary Special Edition

Changes to the 2012 Chevrolet Camaro include the introduction of the 3.6 L direct injection LFX V6 engine replacing the outgoing V6 engine, a new FE4 suspension package for SS coupe and rear stabilizer bars, 20-inch aluminum wheels with P245/45R20 front and P275/40R20 rear tires ), a revised instrument panel appearance, a new steering wheel design with improved ergonomics, a power lift feature for the front passenger seat, a new Rear Vision Package, a new rear spoiler as standard, taillamps from RS appearance package option becomes standard for all vehicles. Crystal Red Tintcoat replaces Red Jewel as an exterior color.
Changes to the RS package include a new, body-color 'sharkfin' antenna.
The 45th Anniversary Special Edition is based on 2LT and 2SS for both coupe and convertible body styles, with unique rally stripe in red and silver at hood and deck, Carbon Flash Metallic body colour, badges located beneath the front fender emblems, new-design 20-inch wheels in dark silver, fog lamp and taillamp bezels finished in dark silver, RS-style taillamp lenses, standard rear spoiler and HID headlamps, body-color roof molding, Jet Black interior with leather-trimmed seats featuring the 45th Anniversary logo, white instrument panel and door trim inserts with the 45th Anniversary logo on the instrument panel, red, white and blue stitching on the seats, steering wheel, shift knob/boot, door armrests and console lid; 45th Anniversary logo on the steering wheel and sill plates.
The 45th Anniversary Special Edition was unveiled in Camaro5 Fest II in Arizona.
Japanese models went on sale in January 2012. Early models included coupe, convertible, 45th Anniversary Special Edition.

2011 SEMA concepts (2011)

The COPO Camaro Concept is a factory-built Stock Eliminator race car and the spiritual successor to the legendary special-order models from 1969, with provisions for two engine configurations, provisions for 3 transmission types, high-rise cowl-induction hood, custom Aeromotive fuel system with a fuel cell and integral high-pressure fuel pump, full chromoly roll cage, coil-over front suspension with Strange Engineering adjustable struts, custom rear suspension based on NHRA requirements, Strange Engineering S-9 solid rear axle, COPO-specific racing wheels, 29x9-inch rear radial racing slicks and 4.5x28x15-inch front tires, manual steering system, Strange Engineering lightweight racing brakes system with standard line lock, removal of sound deadening and power accessories, 2 racing bucket seats, a safety harness for the driver, a competition floor shifter and Chevrolet Performance gauges by Auto Meter.
The Camaro Hot Wheels Concept is a concept vehicle based on the Camaro SS coupe with a Tremec TR-6060 six-speed manual transmission, inspired by the "Custom Camaro" 1/64-scale model that was part of the original Hot Wheels collection released in 1968. It was designed by General Motors' Design studio in Michigan and the Hot Wheels Design studio in California. Changes include Over Chrome Green body colour with ghosted Hot Wheels logo on the quarter panels, Satin black ground effects, Satin black wheels with milled face and Torch Red stripe: 20x10-inch and 20x11-inch, ZL1 grille with Hot Wheels badging, Hot Wheels badge on the decklid, Euro-style taillamps with new inner smoked lens, Euro-style rear fascia with new diffuser and exhaust bezels, ZL1 rear spoiler, Chevrolet Accessories Modified Satin Black Stripe, black aluminum "CAMARO" fender badges with milled face, black aluminum hood insert with milled hood vent extractors, Chevrolet Accessories Synergy Series gill decals, Black leather-wrapped IP and door inserts with Torch Red accents, and cut-and-sew flames; Hot Wheels sill plates, Hot Wheels cut-and-sew embroidered logos in the front seatbacks, Chevrolet Accessories pedal kit, Chevrolet Accessories footwell and cup holder lighting, Brembo brakes: six-piston front with two-piece rotors and four-piston calipers, suspension lowering kit by Pedders Chevrolet Accessories strut tower brace, Chevrolet Accessories black engine cover, Chevrolet Accessories exhaust system.
The Camaro Red Zone Concept is a version of the 2012 Camaro designed by Adam Barry. It features a black convertible tonneau cover, Chevrolet Accessories 21x8.5-inch silver/polished-face wheels, silver heritage stripe, Chevrolet Accessories body-color grille and convertible wind screen, suspension lowering kit by Pedders, concept polished strut tower brace, concept "RS" underhood liner, Titanium leather interior with Silver Ice accents, Black soft instrument panel insert, Chevrolet Accessories Silver Ice door and instrument panel inserts and Chevrolet Accessories floor mats with silver "CAMARO" logos.
The Camaro Synergy Series Concept is a version of the Camaro with Silver Ice body color with black Synergy stripes on the hood, with decklid and "mail slot" decals with red line inserts; Synergy gill decals and no SS or RS exterior badges, Chevrolet Accessories body-color ground effects and grille, Chevrolet Accessories 21-inch wheels in black with red stripe, Suspension lowering kit by Pedders, red Brembo brake calipers, Chevrolet Accessories red engine cover, Concept "SS" underhood liner, Concept polished strut tower brace, Chevrolet Accessories floor mats, Chevrolet Accessories lighting kit, Hurst short-throw shifter, Black leather interior with red accent stitching on seats, console, doors, steering wheel and shifter boot; Silver Ice instrument panel and door inserts, Black leather instrument panel soft insert with red stitching, SS logo with red outline on the head restraints and Chevrolet Accessories pedal kit.
The Camaro 1LE Concept is a version of the Camaro featuring production components from both the Camaro SS and the Camaro ZL1, with Victory Red body color, flat black hood and hash mark extensions, satin black splitter, rocker panels, rear spoiler and outside mirrors; sport suspension featuring Magnetic Ride Control, electric power steering, six-speed manual close-ratio transmission, 20x10-inch and 20x11-inch racing wheels, Goodyear Eagle F1 Supercar G asymmetrical tires, Brembo six-piston front calipers with two-piece front rotors and four-piston rear calipers, dual exhaust outlets with ZL1-style active exhaust and diffuser, shock tower brace, Chevrolet Accessories red engine cover, Black leather interior with Light Stone stitching, Graphite Silver door and instrument panel inserts, ZL1 shifter with Light Stone stitching, ZL1 flat-bottom steering wheel and Chevrolet Accessories pedal kit.
Camaro ZL1 Carbon Concept is a version of Camaro ZL1 with Ashen Gray body colour, Chevrolet Accessories exposed-weave carbon fiber "Mohawk" hood insert, Carbon fiber rear spoiler with stainless-steel wicker bill, Carbon fiber inserts on the interior door and instrument panel, 20x10-inch and 20x11-inch wheels in satin black with machined faces, Brembo six-piston front calipers with two-piece front rotors and four-piston rear calipers, Magnetic Ride Control, dual exhaust outlets with active exhaust and diffuser, Jet Black leather interior with sueded microfiber seat inserts and Torch Red stitching, ZL1 short-throw shifter with suede and carbon fiber-trimmed shift knob and Suede-trimmed flat-bottom steering wheel and ZL1 pedals.

ZL1 (2012–2015)

Unveiled at the 2011 Chicago Auto Show, the ZL1 is a high-performance variant of the Camaro SS. At least 30 percent of the parts on the ZL1 are exclusive to the model.
The car features a LSA V8 engine with a supercharger which produced a maximum boost pressure of. The engine has a power output of at 6,000 rpm and of torque at 4,200 rpm. Power is delivered to the rear wheels by either a six-speed manual or a 6L90 automatic transmission. The manual transmission has a stronger outputshaft, a more robust rear housing and an additional mainshaft roller bearing to provide 30-percent more torque capacity than the automatic transmission used in the Camaro SS. To improve shift quality, there are triple synchros in some gears and a revised linkage. A new dual-mass flywheel is bolted to a high-capacity twin-disc clutch. The automatic transmission has additional clutch plates, a strengthened output shaft and is programmed with three operating modes.
The ZL1's power is complemented by exclusive performance technologies, including the third generation of Magnetic ride suspension and Performance Traction Management. Brembo supplied the braking system having six piston calipers at the front and four piston calipers at the rear. A duct system delivers air from the grille to the hard-working rotors. The 20-inch forged-aluminum wheels are fitted with second-generation Goodyear Eagle F1 Supercar tires. Damping is provided by Magnetic Ride Control units. This system can sense the need for a damping correction 1,000 times per second and make that change in only five milliseconds. The Performance Traction Management system was originally engineered for the Corvette ZR1. In addition to modulating engine torque for optimum launch performance in manual-equipped ZL1s, PTM also varies the traction control and suspension damping as needed. The five available modes are for wet, dry, sport with or without stability control and race-driving conditions.
Additional track-ready features standard on the Camaro ZL1 include coolers for the engine, transmission and rear differential, cooling ducts for the Brembo brakes, and a high-performance fuel system delivering fuel to the LSA engine under any performance-driving condition. The ZL1's rear axle includes a high-capacity cast-iron-case differential, large asymmetrical half shafts, and extra-heavy-duty universal joints. To keep the lubricant temperature in line, there's an oil-to-oil heat exchanger built into the bottom of the differential. Transmission fluid circulates through that heat exchanger and through the radiator to drop operating temps by more than. In addition, the engine is fitted with the same oil-to-coolant heat exchanger used in the Corvette ZR1. The ZL1 has a deeper oil pan, a longer pickup, and a higher-capacity pump than the SS.

2012 Camaro 2LS (2012)

The Camaro 2LS was introduced in 2012. Designed for a better fuel economy using a slightly different gear ratio, this model resembles the trim of the original LS. It was available in both a manual transmission as well as an optional 6-speed automatic transmission with shift paddles on each opposite side of the steering wheel. One downside about the 2LS is that it does not contain the option for “Sports Mode”. Instead of sports mode, the vehicle goes into Electronic Range Select. This allows the driver to choose the highest gear that the transmission will shift into.

2012 COPO Camaro (2012–2013)

The 2012 COPO Camaro is a limited production version of the Camaro factory drag-racing cars designed for NHRA Stock Eliminator and Super Stock classes. It has a Powerglide automatic transmission with a choice of 3 engines. It also has a choice of 5 body colors, a solid rear axle, a full chrome moly roll cage, removal of sound deadening and power accessories, 2 racing bucket seats, a safety harness for the driver, a competition floor shifter, Chevrolet Performance gauges, Bogart racing wheels and Hoosier Racing Tires.
COPO graphics package includes color from the concept vehicle, but in Metallic White, Semi-Gloss Black, Inferno Orange Metallic and Chevy Racing Blue.
Collector's Package includes all three COPO racing engines serial-number-matched to the car, with one installed at the time of delivery.
The COPO Camaro went on sale via a confirmation letter to the registered buyer. Delivery began at the General Motors Performance Build Center in Wixom, Michigan, starting in Summer 2012. Only 69 units were made.

2012 COPO Camaro Convertible (2012–2013)

The COPO Camaro Convertible is a convertible variant of the COPO Camaro. It features a supercharged LSX 5.3 L V8 engine with a 4.0 L Whipple supercharger that has a power output of as well as a black or Inferno Orange Metallic body colour with additional custom graphics, special interior trim and a Turbo 400 three-speed automatic transmission. Two units were made which were numbered 68 and 69.
Car number 69 was unveiled at the 2012 SEMA show and was kept at the GM Heritage Center. Car number 69 went on sale at the 2013 Barrett-Jackson Scottsdale Auction in an American Heart Association charity lot.

Records

In the fall of 2011, a ZL1 completed a lap of the Nürburgring in 7:41.27, placing it in the same class as much more expensive cars like the Porsche 911 Turbo S, Lamborghini Murciélago LP640, and the Mercedes-Benz SLS AMG.

Production

Production of the ZL1 for the 2012 model year amounted to 1,971 units. 99 were officially allocated for Canada.
Engines for 2012 COPO Camaro engine were assembled at Performance Build Center in Wixom, Michigan.
The COPO Camaro models were built by hand starting with hardware from the Oshawa assembly plant, including the same "body in white" body shells racers can purchase from Chevrolet Performance.
A 2012 COPO Camaro engine was built by Hendrick Motorsports owner and Hendrick Automotive Group chairman Rick Hendrick.
Among the 69 2012 COPO Camaros produced, 67 were coupés and 2 were convertibles, 43 cars were equipped with the 427 naturally aspirated engine, 20 cars were equipped with the 327 / 4.0 L-supercharged engine, 6 cars were equipped with the 327 / 2.9 L-supercharged engine, 8 customers ordered the collector's package, 32 cars were painted Summit White, 20 cars were painted Black, 12 cars were painted Victory Red, 2 cars were painted Ashen Grey Metallic, 2 cars were painted Silver Ice Metallic, 1 car was painted Inferno Orange Metallic, 12 cars were ordered without COPO graphics.
The final 2012 COPO Camaro Convertible was sold at the 2013 Barrett-Jackson Scottsdale Auction for US$400,000.

Marketing

Hot Wheels produced a collector's edition 1:64-scale model car based on the Camaro Hot Wheels Concept.

2013 model year update

Camaro, RS, 1LE

Changes made in the 2013 model year include:
The 1LE package was offered on 1SS and 2SS coupe models, with an exclusive Tremec TR-6060/MM6 6-speed manual transmission with a standard air-to-liquid cooling system, 3.91 geared limited slip differential, exclusive monotube rear dampers, 27-mm solid front stabilizer bar, 28-mm solid rear stabilizer bar, higher-capacity rear-axle half shafts, strut tower brace, ZL1-based 20 x 10-inch front and 20 x 11-inch aluminum wheels, 285/35ZR20 Goodyear Eagle Supercar G:2 tires front and rear, ZL1 wheel bearings, toe links and rear shock mounts; ZL1 high-capacity fuel pump and additional fuel pickups, matte black hood, black front splitter and rear spoiler, 10-spoke ZL1-based wheels; ZL1 flat-bottom steering wheel trimmed in sueded microfiber, short-throw shifter from the ZL1 trimmed in sueded microfiber.
The RS package added 20-inch wheels, body-color roof moldings and antenna and high-intensity discharge headlamps.
Changes to the SS models included standard variable-effort electric power steering, optional Recaro bucket seats, optional dual-mode exhaust system on manual transmission-equipped models. Both features were introduced on the Camaro ZL1.
Exterior colors include Summit White, Black, Crystal Red Tintcoat, Victory Red, Rally Yellow, Inferno Orange Metallic, Ashen Grey Metallic and Metallic. The convertible top color choices include black and beige.
The Camaro has a power output of when equipped with the 6 speed manual transmission, which reduced to when the car was equipped with the 6 speed automatic transmission.

NASCAR Nationwide Series car

Unveiled at the 2012 NASCAR Nationwide Series Practice at Indianapolis Motor Speedway, the NASCAR Nationwide Series Camaro coupé incorporated the unique power-bulge hood and deep recessed grille from the production Camaro. In addition, the design incorporates the distinctive halo light rings and dual-port grille appearances, and the gold bowtie.

2012 SEMA concepts

Chevrolet built a special version of the Camaro ZL1 coupe designed in association with Chevrolet Design Manager Dave Ross for NASCAR driver Tony Stewart. It features a custom gray metallic body colour accented with tribal and Smoke graphics in flat red and silver pinstripes, tinted headlamp lenses with red halo lighting, custom wheels with a Piano Black finish and red accents, Jet Black leather seats with suede inserts and scarlet accent stitching, embroidered Tony Stewart signatures on the seats, suede leather door panel inserts and instrument panel wrapping with laser-etched details, Jet Black leather door armrests with French stitching and white piping, Jet Black suede leather-wrapped steering wheel with scarlet accent stitching, Piano Black trim plates and a custom gauge cluster bezel.
The Camaro ZL1 Touring Convertible concept is a Camaro ZL1 convertible with green exterior color, 10-spoke Chevrolet Accessories wheels with liquid metal finish and milled faces, windshield header frame, taillamp bezels and exterior badges with liquid metal finish; matte black splitter and rockers, matte black upper fascia blackout, polished shock tower brace under the hood, ebony leather seats with Mojave perforated leather inserts and light Mojave stitching, Mojave leather-wrapped armrests, leather shift knob and console lid with Mojave stitching, Chevrolet Accessories Ice Blue interior lighting kit, ZL1-logo premium floor mats and sill plates.
The Camaro Performance V8 concept is a black Camaro SS with Chevrolet Performance ZL1 rear differential kit, 5.1-ratio short-throw shifter, shock tower brace with white Camaro graphic, Camaro 1LE suspension kit, Camaro ZL1 brake conversion kit, concept dual-mode exhaust system, Camaro ZL1 rockers and rear lower diffuser, Camaro Dusk front splitter, upper front fascia blackout graphic, hood and decklid graphics in red metallic, Chevrolet Accessories black blade rear spoiler, heritage grille and 'gill' graphics, Chevrolet Accessories 20x10-inch and 20x11-inch five-spoke black wheels with polished 'fangs', Camaro ZL1 black suede seat inserts with Jet Black leather seats; Torch Red stitching and carbon fiber-material bolsters, red suede stripe on the driver's seatback, Camaro ZL1 flat-bottom steering wheel with carbon fiber trim, Camaro ZL1 suede shift knob with 5.1 badge, leather carbon fiber-material-wrapped instrument panel and door inserts, suede-wrapped soft instrument panel insert, Chevrolet Accessories lighting package, pedal covers and Camaro-logo premium floor mats; Concept Chevrolet Performance embroidered console lid and sill plates and production RS gauge package.
The Camaro Performance V6 concept includes a LFX V6 engine, ZL1 Brake Conversion Kit, Camaro 1LE suspension kit, rear differential from the Camaro 1LE, Summit White body colour, Chevrolet Performance shock tower brace, Camaro ZL1 dual-mode exhaust system and rear diffuser, Camaro convertible rear spoiler in matte black, Chevrolet Accessories heritage grille painted matte black, Camaro Dusk front splitter in matte black, upper front fascia blackout graphic, matte black hood wrap with exposed Summit White stripe, Chevrolet Accessories 20x10-inch and 20x11-inch 10-spoke black wheels with milled faces, Summit White door panel and instrument panel inserts, Chevrolet Accessories lighting package, pedal covers and Camaro-logo premium floor mats; Concept Chevrolet Performance embroidered console lid and sill plates, Concept Chevrolet Performance logo on the instrument panel insert and production RS gauge package.
The Camaro SS 1LE package became available under the 2013 Chevrolet Performance Catalog.

Giovanna Edition (2013)

Unveiled at the 2013 Tokyo Auto Salon, the Camaro Giovanna Edition is a variant of the Camaro LT RS and SS RS for the Japanese market. It was developed in collaboration with the owner of the Cadillac/Chevrolet dealership in Tokyo's Kunitachi suburb, with further input from noted Japanese journalist Tatsuya Kushima. It included a choice of 4 body colors, body stripe, fuel cap with Giovanna Edition Logo, front SS or RS emblem, rear Chevrolet bow tie decal, Giovanna Edition Logos on the head rests and door sill plates and Giovanna Wheel 20-inch aluminium wheels made by WTW Corp. It went on sale in March 2013.

2013 "Turbo" Camaro Coupé (2013)

Unveiled at the 2013 Chicago Auto Show, the "Turbo" Camaro Coupé is a concept car based on the Camaro coupé and inspired by the DreamWorks Turbo movie snail. Changes included lower rockers and fender flares in a wide body design configuration, a front splitter and rear diffuser, a GT concept rear spoiler, custom front and rear LED lighting with multicolor halo effect for the front headlamps, black body colour with a vinyl chrome wrap dark tinted to look like black chrome, 24x10-inch front wheels with a front wheel and custom offset, 24x15-inch rear wheels, a supercharged V8 engine mated to an automatic transmission having a power output of, a custom intake assembly for the supercharger housing, 2x2 5-inch diameter rear exhaust outlets, custom COPO hood assembly, low profile hood pin system, front suspension with custom adjustable coilover strut assemblies and rear suspension with custom adjustable rear springs and shock assemblies.

2013 Camaro Hot Wheels Special Edition

The Camaro Hot Wheels Special Edition is a special variant of the Camaro available in coupé and convertible body styles, with a choice of 2LT and 2SS trims with a ZL1 appearance package. Changes include:
HotWheelsSpecialEditionFinalProductionNumbers
ModeleditionTransCount
1ES372SS COUPEHWSMYCAUTO SS559
1ES372SS COUPEHWSM10MANUAL SS354
1EF372LT COUPEHWSMYBAUTO V6263
1ES672SS CONVERTHWSMYCAUTO SS203
1ES672SS CONVERTHWSM10MANUAL SS57
1EF672LT CONVERTHWSMYBAUTO V646
1EF372LT COUPEHWSMV5MANUAL V634
1EF672LT CONVERTHWSMV5MANUAL V68
1524

The Hot Wheels Edition was unveiled at the 2012 SEMA Show, followed by the 2013 Indianapolis 500.
Production began in the first quarter of 2013, and ordering began in October 2012.
Japanese models went on sale in limited quantities, which included Kinetic Blue Metallic body colour, black 20-inch wheels, HOT WHEELS decal stripe, exclusive rear spoiler, front leather seats with HOT WHEELS embroidering, engine cover in black, premium floor mat and the LFX V6 engine.

2013 COPO Camaro (2013)

The 2013 COPO Camaro is a limited production variant of the Camaro factory drag-racing cars designed for NHRA Stock Eliminator classes, with a new manual or Powerglide automatic transmission and a choice of 3 engines. It also features a fuel-injection system, engine management from a Holley HP EFI electronic control unit with self-tuning fuel table strategies and data logging, Holley Hi-Ram intake manifold, rear axle gearing optimized for each vehicle depending on the engine and transmission, a 'heritage' grille and standard-production headlamps, new exterior graphics choices with engine-size call-outs, revised interior package with custom carpet and new switch panel, dedicated racing wiring harness, and revised front springs that enhance performance, transmission cooler integrated with radiator, choice of 5 body colors, NHRA-approved roll cage and other safety equipment, racing chassis and suspension components, lightweight Bogart racing wheels, Hoosier Racing Tires and a sequenced build serial number matched to the engine. The car is sold without a Vehicle identification number though, and thus cannot be registered for highway use.
Engine Collector's Package includes all three COPO racing engines serial-number-matched to the car, with one installed at the time of delivery.
The special edition went on sale by signing up on the COPO Camaro Mailing List in February 2013, with randomly chosen buyers identified by March of the same year. Production began in April 2013, with deliveries starting in early Summer. Production amounted to a total of 69 units.

Motorsports

The Camaro coupé started participating in the NASCAR Nationwide Series beginning in the 2013 season.

Aftermarket production

The 2013 COPO Camaro #041 was built by Richard Rawlings of Gas Monkey Garage and Dennis Collins of Collins Bros. Jeep at the Wixom plant. The vehicle was sold for US$137,500.00 at 2013 Barrett-Jackson Reno auction. The production of the vehicle was featured in Fast N' Loud.

Production

Production Numbers
Changes for the 2014 model year include a redesigned front and rear end in corporative new head and tail light assembly, resulting in a wider, lower, more contemporary appearance, and a front fascia featuring a wider lower opening as well as a narrower upper opening that also updates the appearance of the iconic “halo ring” HID headlamps on the Camaro RS package. Other additions include a functional hood vent on the Camaro SS and optional Recaro seats with microfiber suede inserts for the SS and ZL1 packages. The Head-Up Display and Driver Information Center were also now in color display for the 2LT, 2SS and ZL1 models.
US models of the 2014 Camaro arrived at Chevrolet dealers later in 2013. The Camaro Z/28 was expected to appear at track events across the United States in spring 2014.
European Camaro convertible and coupé included new MyLink connected radio, and were set to arrive at Chevrolet dealerships at the end of 2013.

Camaro Z/28

Unveiled at the 2013 New York Auto Show, followed by the 2013 Frankfurt Motor Show, the Camaro Z/28 is a high performance variant of the Camaro SS with a full aerodynamic package designed for optimum performance during track driving. The package includes a large splitter connected to an underbody panel, fender flares over the front and rear wheels, extended rocker panels, redesigned rear spoiler and a functional diffuser. Other changes include interior trim in matte-metallic Octane finish, a flat-bottomed steering wheel, standard Recaro seats with microfiber suede inserts and manual adjustment, elimination of the seat-back pass through, high-density foam in place of the rigid structure of the seat back and steel mesh of the seat bottom, a 7.0 L LS7 V8 engine co-developed with Corvette Racing, racing-style cold-air induction system with large K&N air filter, standard dual mode exhaust system with larger-diameter pipes, Tremec TR-6060 6-speed manual transmission, limited-slip differential with a helical gear set, 19-inch diameter wheels with Pirelli P Zero Trofeo R 305/30ZR19 tires, Multimatic DSSV spool valve dampers, Brembo Carbon Ceramic Matrix brake discs, monoblock calipers, elimination of tire inflating kit, deletion of interior sound deadener and carpeting from the trunk, replacement of the standard LN4 battery with LN3 battery, replacement of the standard 3.5 mm glass with thinner 3.2 mm glass for the rear window, removal of HID headlamps and foglights and the removal of air conditioning.
The Z/28 can accelerate from in 4 seconds and can attain a top speed of.
The Z/28 won the Motor Trend's 2014 Best Driver's Car Award, beating the Alfa Romeo 4C, BMW i8, BMW M4, Nissan GT-R Nismo and five other cars.

Marketing

Takara Tomy produced a self-transforming Camaro coupe under the Transformers Omnibot line, produced in association with Kenji Ishida of Brave Robotics. The toy was unveiled at the Tokyo Toy Show in 2013.

Sales

Awards and recognition