Bentley Mark VI


The Bentley Mark VI is an automobile from Bentley which was produced from 1946 to 1952.
The Mark VI 4-door standard steel sports saloon was the first post-war luxury car from Bentley. Announced in May 1946 and produced from 1946 to 1952 it was also both the first car from Rolls-Royce with all-steel coachwork and the first complete car assembled and finished at their factory. These very expensive cars were a genuine success; long-term, their weakness lay in the inferior steels forced on them by government's post-war controls. Chassis continued to be supplied to independent coachbuilders. Four-door Saloon, two-door saloon and drophead coupe models with bodies by external companies were listed by Bentley along with the Bentley-bodied saloon.
This first Bentley factory finished car was given the name Bentley Mark VI standard steel sports saloon. This shorter wheelbase chassis and engine was a variant of the Rolls-Royce Silver Wraith of 1946 and, with the same standard steel body, became the cautiously introduced Silver Dawn of 1949. In 1952 both Rolls Royce Silver Dawn and Bentley Mk VI standard steel bodies were modified to incorporate a boot of about twice the size and the result became known as the R type Bentley based on the Chassis number at which the change took place. The name of the Rolls Royce Silver Dawn was not changed after the modification that started with the "E" series in these cars.
Mark VI engines and chassis were modified to provide higher performance and sold to be bodied by selected coachbuilders as the first Bentley Continentals.

Engine

The Mark VI -litre used an F-head straight-6 engine 4.3 L in size. The manufacturer refused to disclose a horse power value for the car but an Autocar Magazine road test reproduced in 1950 reported that top gear provided "flexibility down to 6 mph " and the ability to "climb a hill of 1 in 9 maximum gradient, complicated by bends", all of which supported the manufacturer's contention that power, along with low speed torque, were adequate.
.
In 1951, a -litre, 4.6 L version of the engine was introduced. The increase in displacement was accomplished by increasing the bore from 3 1/2 inch to 3 5/8 inch. The later version is sometimes casually referred to as the "big bore" engine, the earlier version as the "small bore" version. The 4 1/2 L version of the engine is as well equipped with a Vokes 30 full flow oil filter.
Carburation in RHD cars were two horizontal constant-vacuum SU carburetors. LHD cars had a single dual downdraught Stromberg carburetor type AAV26M and a different inlet manifold as fitted in the Rolls Royce Silver Dawn and Silver Wraith.
A four-speed syncromesh manual transmission was fitted in all Bentley MK VI with the change lever to the right of the driver on RHD cars and on the column on LHD versions.
-litre cars had chassis numbers from B 1 AJ through B 400 LJ, with the final two letters indicating the series in which it was built. The "big bore" cars serial numbers begin with B 1 MB and ended with B 300 PV. Each alphabetic series only contained either even or odd numbers, and 13 was always skipped for the odd-numbered sequences.
The was referred to as the L and can be quickly identified from its single exhaust in RHD cars. The is known as the L and features a twin exhaust in RHD cars. In LHD cars the twin exhaust system was only fitted with the introduction of the R-type.
In addition for "standard steel" Mark VI saloons the single hinged ventilation flap centrally mounted on the top of the bonnet, directly ahead of the windscreen was replaced, on later cars, with two hinged ventilation flaps, mounted at or slightly below knee height, one on each side of the bonnet, ahead of the front doors. The oil filler cap is another way to identify engine type; a plastic cap is typical of a "small bore" engine, a metal cap of a "large bore" engine.

Chassis and running gear

The chassis used leaf springs at the rear and independent coil springing at the front. A control on the steering wheel centre adjusts the hardness of the rear springing by hydraulically adjusting the rear dampers. This is done via opening a check valve that provides pressure by diverting transmission oil to the dampers. A pedal-operated central lubrication system type Bijur-Girling allows oil to be applied to moving parts of the suspension from a central reservoir by using a foot pedal. The drum brakes were assisted by the traditional Rolls-Royce mechanical servo at the transmission.

Standard Steel Saloon

Employing its experience with the steel bodies made in short runs since 1936 by then partly-owned subsidiary Park Ward the Car Division of Rolls-Royce offered their lowest priced chassis with a factory-supplied body all-steel so it could be exported all over the world. The factory bodies with a Gurney-Nutting-Blatchley refined shape were made by Pressed Steel Ltd of Cowley and sent to the Bentley works at Crewe for painting and fitting out with traditional wood and leather. They featured rear hinged "suicide" doors at the front with concealed hinges, a sliding sunroof, a permanently closed windscreen with an electric defrosting and demisting unit hidden in the scuttle and a second heater that made use of the coolant and was fitted with an electric fan beneath the left front seat. Twin screenwipers were fitted and provision was made for the fitting of a radio with a short and flexibly mounted aerial that could be swung up above the centre of the screen.

Road test

A 4.6-litre, factory bodied car tested by The Motor magazine in 1951 had a top speed of and could accelerate from 0- in 15.0 seconds. A fuel consumption of was recorded. The test car cost £4,473 including taxes.

Commercial

The Mark VI was introduced at a time of steel shortage across Europe which translated into a serious shortage of new cars for sale on the UK market. A Used Car report in 1951 of a three-year-old example with 10,450 miles on the odometer noted that a car which had, when new, retailed for £4,038 including sales taxes, was now offered for sale at £5,335. This was seen as a comment on the quality of the car but also on the continuing shortage of cars for sale.
By the end of 1952 order-books had shrunk and the Mark VI was replaced by the R-Type, featuring an extended boot/trunk supported by an chassis that was extended by six inches behind the rear wheels. In addition, an automatic transmission option was now available, an automatic choke along with other less visible modifications were added and former export-only options were now available to the home-market. The R-type led up to the introduction of the completely redesigned S series in 1955.
Bentley Mark VI Production volumes:
A Mark VI chassis was developed by H I F Evernden and J P Blatchley in 1950 and 1951 carrying a larger engine with a higher compression ratio and modified fuel and exhaust systems, a close ratio gearbox and much higher final drive ratio.
By special arrangement with Bentley 2-door bodies were fitted having a lower frontal area and of significantly lighter construction, the first – made by H J Mulliner – developed in conjunction with Evernden and Blatchley. The first still luxurious car was more than 10% lighter than the standard car. They were the most expensive production cars in the world and the world's fastest 4/5-seater saloons with a top speed above 120 mph.
These chassis were produced between June 1952 and April 1953 and bear the chassis numbers BC1A to BC26A, with the prototype, totalling 27 cars. The engine compression was reduced on the last 8 cars. The bulk of the chassis were clothed by H J Mulliner but some were bodied in Europe. Only the 27 cars were built before the R designation was added to the chassis series identification.

Gallery