BMW N47


BMW N47 is a four-cylinder common rail diesel engine that has many improvements over its predecessor, the M47. In 2014 it was replaced with the B47.

First use

The N47 engine debuted in March 2007 in the facelifted 1 Series BMW E87 and E81 and was available in the 1 Series BMW E82 and E88, which were introduced later in the same year.

Usage in other models

The engine also became available in the 5 Series BMW E60 and E61 from September 2007, several months after the 5 series was face lifted, during which time the older M47 remained available.
In the 2008 model year 3 Series E90/E91/E92/E93 when the entire 3 series range gained the company's Efficient Dynamics technology.
Not long after it became available in the X3 and has since then become available in the X1.
The N47 comes as a and unit, the latter identical in capacity to the BMW M47TU/TU2 series.

85kW version

The tune is for the entry level E81 and E87 116d, as well as the entry level 3 Series E90 316d. It was also used in the 3 Series F30 316d.

105kW version

The model was used in the
A new derivative was introduced in September 2009 for the 2010 model year.
This version featured exceptionally low emissions of only and fuel consumption of 68.9 mpg
This version was used in the E90 BMW 320d Efficient Dynamics

130kW version

The "standard" x20d model has extra power, producing but of torque less at. This is found in the
In Europe, this particular version is one of the most popular engines in the entire range; the best selling 3 series is the 320d, while the 520d is the UK's best selling 5 series.
The updated version of this engine introduced in March 2010 produces at 4000 rpm and at 1750-2750 rpm.

Twin turbo version

In October 2007, BMW introduced a twin sequential turbo model. With, it is the first production diesel on sale to achieve a specific output of over per liter. It uses the same turbo technology first shown in the E60 535d.
The model was used in the

Timing chain problems

The N47 engine family is prone to excessive timing chain wear and premature failure. Rattling noise from the rear of the engine is indicative of the condition. Timing chain failure may call for engine replacement or a costly repair. The most seriously affected units which require the most extensive repairs were produced from 01.03.2007 to 05.01.2009. However there have been frequent reports of timing chain failure in 1, 3 and 5 series BMW engines manufactured from as early as 2004 until at least 2011 in both the petrol and diesel versions. At times the failure has resulted in a dangerous cut out of the engine while the vehicle was being driven - sometimes at relatively high speed. A "Quality Enhancement" was issued by BMW for some, but not all vehicles, but has since been discontinued.

Other issues

The return spring on the turbo's wastegate was not originally lubricated or covered, this frequently resulted in early failure causing the waste-gate to remain partially or fully open. With the subsequent loss in compression, fuel consumption increased by 30–50%. The problem was described by BMW engineers as a "known fault" and was immediately repaired, however BMW refused to compensate customers for the excessive fuel consumption and denied this fault was their liability.
As the cars equipped with this engine are coming of age, some hoses in the engine bay can start to break down. This is not to be ignored, even though this does not illuminate the CEL, it just sets a code in the ECU. If the vacuum hose supplying the EGR cooler bypass valve gets a hole rubbed in it, or breaks down from old age and oil spray, the EGR cooler won't get bypassed during the engine warmup period. This causes excessive buildup in the cooler matrix, and when the engine warms up these solid chunks of buildup can detach from the EGR cooler and get sucked into the plastic intake tube, melting holes in the intake tube, causing a massive boost leak and in very rare cases an engine fire.