Analytical thermal desorption


Analytical thermal desorption, known within the analytical chemistry community simply as "thermal desorption", is a technique that concentrates volatile organic compounds in gas streams prior to injection into a gas chromatograph. It can be used to lower the detection limits of GC methods, and can improve chromatographic performance by reducing peak widths.

History

Analytical thermal desorption originated in the mid-1970s as an adaptation to the injection procedure for GC. Injector liners were packed with a compound able to adsorb organic compounds, used to sample air or gas, and then dropped into the inlet of the GC. This principle was first widely employed for occupational monitoring, in the form of personal badge-type monitors containing a removable charcoal strip. These offered the advantage of being amenable to analysis without a separate solvent-extraction step.
Also developed in the 1970s was a method by which volatiles in the air were collected by diffusion onto tubes packed with a sorbent, which was then heated to release the volatiles into the GC system. These were first introduced for monitoring sulfur dioxide and nitrogen dioxide, but the analyte scope later widened as the sorbents became more advanced. Another early method involved passing a stream of gas through a water sample to release the volatiles, which were again collected on a sorbent-packed tube.
Such axial-type samplers, which later became known as 'sorbent tubes', were laid out as an industry standard in the late 1970s, by Working Group 5 of the UK Health & Safety's Committee on Analytical Requirements. The tubes they outlined were inches long with an outer diameter of inch, and were first employed in Perkin Elmer's ATD-50 instrument.
At the same time, WG5 specified various basic functionality requirements for thermal desorption, and in the years since then, a number of improvements have been made to instrumentation for thermal desorption, including two-stage operation, splitting and re-collection of samples, improved trap-cooling technology, standard system checks, and automation.

Principles

Thermal desorption fundamentally involves collecting volatile organic compounds onto a sorbent, and then heating this sorbent in a flow of gas to release the compounds and concentrate them into a smaller volume.
Early thermal desorbers used just single-stage operation, whereby the volatiles collected on a sorbent tube were released by heating the tube in a flow of gas, from where they passed directly into the GC.
Modern thermal desorbers can also accommodate two-stage operation, whereby the gas stream from the sorbent tube is collected on a narrower tube integral to the thermal desorber, called the focusing trap or cold trap. Heating this trap releases the analytes once again, but this time in an even smaller volume of gas, resulting in improved sensitivity and better GC peak shape.
Modern thermal desorbers can accommodate both single-stage and two-stage operation, although single-stage operation is now usually carried out using the focusing trap to collect the analytes, rather than a sorbent tube.
It is normal for the focusing trap to be held at or below room temperature, although a temperature no lower than 0 °C is sufficient for all but the most volatile analytes. Higher trap temperatures also reduce the amount of water condensing inside the trap.

Sampling configurations

A wide variety of sampling configurations are used for thermal desorption, depending on the application. The most popular are listed below.

Single-stage thermal desorption

This involves sampling direct onto the focusing trap of the thermal desorber. It is generally used for situations where the analytes are too volatile to be retained on sorbent tubes.
This involves sampling first onto a sorbent tube. The most widely used tubes are those following the pattern laid out by WG5. After sampling, the tube is desorbed to transfer the analytes to the focusing trap before the second desorption stage transfers them to the GC. The greater sensitivity of this method has made it increasingly popular for sampling dilute gas streams, or in exploratory work where the target atmosphere is unknown.
The sorbent tube and the focusing trap may be packed with one or more sorbents. The type and number of sorbents depends on a number of factors including the sampling setup, the analyte volatility range, analyte concentration, and the humidity of the sample.
One of the most versatile and popular sorbents for thermal desorption is poly, known by its trademark Tenax.

Analyte range

Depending upon the sampling technique and the analytical conditions, thermal desorption can be used to reliably sample analytes ranging in volatility from ethane to about tetracontane. Incompatible compounds include:
Applications of thermal desorption were originally restricted to occupational health monitoring, but have since extended to cover a much wider range. Some of the most important are mentioned below – where available, examples of early reports, and more recent citations have been given: